Atoll IN200 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Atoll IN200 (8 sivua) kategoriassa Vastaanotin. Tämä opas oli hyödyllinen 37 henkilölle ja sai 4.5 tähden keskimäärin 19 käyttäjältä

Sivu 1/8
ATOLL ELECTRONIQUE
IN200 Sig
ATOLL ELECTRONIQUE
OWNER’S MANUAL ~ INTEGRATED
Page 5Page 4
The remote control is equipped with 2 Lithium CR2025 batteries. This remote control is also
able to drive all others ATOLL’s products: CD players, Tuners, Integrated or preamplifiers.
Warning: reduce the volume of the source connected to BY-PASS before any use of the
BY-PASS Input. The BY-PASS input allows you to use your IN200 as a power unit (to be
connected to the output of an audio-video preamplifier, for example). This input is selected
this input has been selected, the word “BY-PASS” appears on the screen and no other
function can be accessed by the remote control. To exit the BY-PASS, press the BY-PASS button
on the remote control for 3 seconds or use the source selector on the front panel (18).
(1)
MUTE key: to get off the Mute, press any active key of the remote control or turn a
front knob.
(2)
Access to inputs OPT1 – OPT2 – COAX1 – COAX2 – USB – BT is only possible if
your appliance is equipped with the digital board.
1) Auxiliary input (optional phono).
2) CD input.
3) Tuner input.
4) DVD input.
5) Tape input (PLAY)
(1)
.
6) Tape output (REC)
(1)
.
7) BY-PASS input.
8) Preamp. outputs (to 1 or 2 power
amplifiers or to a Subwoofer).
9) Switch On/Off and general plug in
(with protection fuse).
10) Left speaker output (
+
& ).
11) Right speaker output (
+
& ).
12) Trigger output: this output is used
to control the switching off/on of any
device equipped with a compatible
Trigger input (see instructions for use).
17) Headphones jack: speakers outputs are switshed off when a headphone is plugged in.
18) Knob for ON/OFF (by pushing), and sources selection (by rotation).
19) Knob for standby ON, volume and balance setup.
REMOTE CONTROL
USING OF THE BY-PASS INPUT
CONNECTING
13) Bluetooth receiver.
15) Optical inputs 1 & 2.
14) Coaxial inputs 1 & 2.
16) USB input (B type).
Optional Digital Board:
(1)
Tape input / output - monitoring loop:
The TAPE function allows the recording of music from any selected source.
You can also activate a permanent monitoring loop as follows: select your source
then hold the TAPE button on the remote control for about 3 seconds. The TAPE
symbol lights up and indicates that the monitoring loop is activated. In this
mode, direct access to the TAPE input is no longer possible.
You can use this mode to insert an equalizer between the TAPE IN and TAPE OUT
sockets.
This function is memorized even if you switch off the device from the mains. To
deactivate this mode, simply hold down the TAPE button on the remote control
again for 3 seconds.
Trigger cable must be a Male to Male stereo jack plug
Ø 3,5 mm (1/8”).
Selection of sources
+
(except BY-PASS)
Balance setup (from -9 to +9)
Select
display ON
or OFF
Mute
(1)
Stand-by ON/OFF
BY-PASS selection (press 3 sec.)
Direct access to sources
(2)
Non-
functional
keys
Volume
+
& and balance
setup (from 0 to 80)
17 18 19
Jack
3,5 mm
Optional Digital Board
11 1 2 3 4 5 6 7 8 9 10 12
13 14 15 16

Tuotetiedot

Merkki: Atoll
Kategoria: Vastaanotin
Malli: IN200

Tarvitsetko apua?

Jos tarvitset apua merkille Atoll IN200 esitä kysymys alla ja muut käyttäjät vastaavat sinulle