SoundTube CM31-EZ Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille SoundTube CM31-EZ (1 sivua) kategoriassa Kaiutin. Tämä opas oli hyödyllinen 27 henkilölle ja sai 5.0 tähden keskimäärin 14 käyttäjältä
Sivu 1/1
CM31-EZ
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning
© 2009 SoundTube Entertainment, Inc. All rights reserved. PN INS-CM31-EZ Rev10. 26.09
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
Grille
Installation aid/paint mask
Baffle
SpeedWing™ mounting arms
Speaker seismic restraint hole
1.
2.
1.
2.
1.
2.
Tile bridge
Flexible conduit clamp
Signal wires
Grille safety clip
1. Nail or screw bracket to
joists.
2. Finish installing ceiling.
8. Remove paint mask
unless painting is required.
In that case, follow steps
9-12 when painting is
complete.
9. Adjust tap switch to
proper setting. Switch is
preset to the highest setting
in the 70.7-volt mode.
10. Attach grille safety clip
by placing the large end of
the clip over snap-fit post (1),
then sliding clip until small
end snaps into place around
post (2).
5. Feed speaker wires
through conduit clamp and
connect with wire nuts.
Push wire nuts into backcan
and affix conduit clamp.
3. Use RotoZip or other tool
to cut hole.
7. Insert speaker into
mounting hole. Tighten both
bolts on the baffle face to
actuate the mounting wings.
DO NOT OVERTIGHTEN.
6. If required, attach
seismic restraint system to
the sheet-metal tab on the
rear panel of the speaker,
then to reinforced structure
(safety cable not included).
11. Align tabs on snap-fit
grille with slots in baffle,
gently press grille into place.
1. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete.
4. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete.
2. Use included tile bridge
to mark cutout on
sheetrock. Tile bridge ships
in separate box.
3. Use RotoZip or other tool
to cut hole. Hole diameter:
5.6 in. (142 mm).
4. Feed speaker wires
through conduit clamp and
connect with wire nuts.
Push wire nuts into backcan
and affix conduit clamp.
8. Adjust tap switch to
proper setting. Switch is
preset to the highest
setting in the 70.7-volt
mode.
5. If required, attach seismic
restraint system to hole in
clamping arm, then to
reinforced structure (safety
cable not included).
2. Use included tile bridge
to mark cutout on tile.
1. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete. Tile
bridge ships in separate box.
3. Use RotoZip or other tool
to cut hole. Hole diameter:
5.6 in. (142 mm).
4. Insert speaker into
mounting hole on ground
with tile bridge and paint
mask in place. Tighten both
screws on the baffle face to
actuate the mounting wings.
Firmly secure both screws,
DO NOT OVERTIGHTEN.
Put assembly into tile grid.
5. Feed speaker wires
through conduit clamp and
connect with wire nuts.
Push wire nuts into backcan
and affix conduit clamp.
6. If required, attach seismic
restraint system to hole in
clamping arm, then to
reinforced structure (safety
cable not included).
8. Adjust tap switch to
proper setting. Switch is
preset to the highest setting
in the 70.7-volt mode.
9. Attach grille safety clip by
placing the large end of the
clip over snap-fit post (1),
then sliding clip until small
end snaps into place around
post (2).
10. Align tabs on snap-fit
grille with slots in baffle,
gently press grille into place.
11. Done! 11. Done! 12. Done!9. Attach grille safety clip by
placing the large end of the
clip over snap-fit post (1),
then sliding clip until small
end snaps into place around
post (2).
10. Align tabs on snap-fit
grille with slots in baffle,
gently press grille into place.
7. Remove paint mask
unless painting is required.
In that case, follow steps
8-11 when painting is
complete.
7. Remove paint mask
unless painting is required.
In that case, follow steps
8-11 when painting is
complete.
6. Insert speaker into
mounting hole with paint
mask in place. Tighten both
bolts on the baffle face to
actuate the mounting wings.
Firmly secure both bolts,
DO NOT OVERTIGHTEN.
Box contents
1 Speaker
1 Grille
1 Paint mask
2 Wire nuts
1 UL-listed conduit clamp
Note: Tile bridge included, ships in separate box.
Install Instructions For:
CM31-EZ speaker
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
CM31-EZ
Pre-Construction Bracket Instructions For:
CM31-EZ speaker (Pre-construction bracket sold separately)
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
CM31-EZ
Sheetrock Installation Instructions For:
CM31-EZ speaker
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
CM31-EZ
Drop-tile Installation Instructions For:
CM31-EZ speaker
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
CM31-EZ
Tuotetiedot
| Merkki: | SoundTube |
| Kategoria: | Kaiutin |
| Malli: | CM31-EZ |
Tarvitsetko apua?
Jos tarvitset apua merkille SoundTube CM31-EZ esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kaiutin SoundTube Käyttöohjeet
21 Helmikuuta 2025
28 Tammikuuta 2025
28 Tammikuuta 2025
28 Tammikuuta 2025
28 Tammikuuta 2025
10 Tammikuuta 2025
10 Tammikuuta 2025
10 Tammikuuta 2025
10 Tammikuuta 2025
10 Tammikuuta 2025
Kaiutin Käyttöohjeet
- Kaiutin VIETA PRO
- Kaiutin Axis
- Kaiutin Aiaiai
- Kaiutin Audio Pro
- Kaiutin Revel
- Kaiutin RCF
- Kaiutin Xcellon
- Kaiutin FBT
- Kaiutin Hertz
- Kaiutin Boss
- Kaiutin House Of Marley
- Kaiutin Bearware
- Kaiutin Aconatic
- Kaiutin Kalley
- Kaiutin Grundig
Viimeisimmät Kaiutin Käyttöohjeet
8 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025
5 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025