StarTech.com VDSL-LAN-EXTENDER-1G Käyttöohje
StarTech.com
Wifi-toistin
VDSL-LAN-EXTENDER-1G
Lue alta 📖 käyttöohje suomeksi merkille StarTech.com VDSL-LAN-EXTENDER-1G (2 sivua) kategoriassa Wifi-toistin. Tämä opas oli hyödyllinen 46 henkilölle ja sai 4.8 tähden keskimäärin 23.5 käyttäjältä
Sivu 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: October 13, 2023
10/100/1000 Mbps VDSL2 Ethernet Extender Kit - 1km
Product Information
For the latest drivers/software, technical specications, and declarations of
conformance, please visit: www.StarTech.com/VDSL-LAN-EXTENDER-1G
Requirements
• Ethernet Device x 2
• RJ45 Ethernet Cables x 2
• RJ45 or RJ11 Cable x 1
Package Contents
• VDSL Extender x 2
• Mounting Bracket Kits x 2
• Power Supply x 2
• Quick-Start Guide x 1
Installation
(Optional) Mounting the VDSL Extender
Note: Before mounting the VDSL Extender make sure that the surface you are
mounting to is strong enough to support the VDSL Extender. It is recommended that
the VDSL Extender is mounted on a wall stud to provide the correct support.
1. Determine the Mounting Surface for the Local and Remote VDSL Extender.
2. Place the VDSL Extenders upside down to expose the Mounting Bracket Holes on
the VDSL Extenders. Align the Holes in the Mounting Brackets with the Holes on
the bottom of the VDSL Extenders.
3. Insert four Screws through each Mounting Bracket and into the VDSL Extender.
4. Tighten each Screw using a Phillips Head Screwdriver.
5. Mount the VDSL Extender to the desired Mounting Surface using the appropriate
Mounting Hardware (e.g. Wood Screws).
Install the VDSL Extender Kit
1. Position a VDSL Extender in each of the locations, local and remote.
2. Using DIP Switch 1, ensure that one VDSL Extender is in Master Mode (CO), and the
other is in Remote Mode (RT).
Note: If the DIP switches need to be adjusted after the initial setup, both VDSL
Extenders must be powered o before changing the DIP switch settings.
3. Plug in an RJ45 Ethernet Cable from the LAN Port on the local VDSL Extender to an
Ethernet Port on the local Ethernet Device.
4. Plug in an RJ45 Ethernet Cable from the LAN Port on the remote VDSL Extender to
an Ethernet Port on the remote Ethernet Device.
5. Plug in a RJ45 or RJ11 Cable from the VDSL2 Port of the local VDSL Extender, to the
VDSL2 Port of the remote VDSL Extender.
6. Connect the included Power Adapters to each of the VDSL Extenders.
Product ID
VDSL-LAN-EXTENDER-1G
Component Function
1 DIP Switches
• Set the Mode or change settings on the VDSL
Extenders
• Refer to DIP Switch Chart
2 LAN Port
• Connect to an RJ45 Port on Local and Remote
Equipment
3 LAN Status LEDs • Refer to the LED Chart
4 VDSL2 Status LEDS • Refer to the LED Chart
5 VDSL2 Port
• Use a RJ45 or RJ11 Cable to connect the Local
and Remote VDSL Extenders together
6 Power Input Port
• Connect the included Power Adapter
• Located on the rear of each VDSL Extender
2
1 3 4 5
Tuotetiedot
| Merkki: | StarTech.com |
| Kategoria: | Wifi-toistin |
| Malli: | VDSL-LAN-EXTENDER-1G |
Tarvitsetko apua?
Jos tarvitset apua merkille StarTech.com VDSL-LAN-EXTENDER-1G esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Wifi-toistin StarTech.com Käyttöohjeet
24 Tammikuuta 2025
20 Tammikuuta 2025
Wifi-toistin Käyttöohjeet
- Wifi-toistin Cudy
- Wifi-toistin Ubiquiti Networks
- Wifi-toistin Mercusys
- Wifi-toistin Tenda
- Wifi-toistin Xiaomi
- Wifi-toistin HELGI
- Wifi-toistin Evga
- Wifi-toistin Netgear
- Wifi-toistin D-Link
- Wifi-toistin Strong
- Wifi-toistin CSL
- Wifi-toistin Axis
- Wifi-toistin Icron
- Wifi-toistin Fluke
- Wifi-toistin Extron
Viimeisimmät Wifi-toistin Käyttöohjeet
29 Maaliskuuta 2025
29 Maaliskuuta 2025
24 Maaliskuuta 2025
21 Helmikuuta 2025
20 Helmikuuta 2025
20 Helmikuuta 2025
20 Helmikuuta 2025
20 Helmikuuta 2025
6 Helmikuuta 2025
5 Helmikuuta 2025