PAC NU-CTS2 Käyttöohje

PAC Ei luokiteltu NU-CTS2

Lue alta 📖 käyttöohje suomeksi merkille PAC NU-CTS2 (2 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 38 henkilölle ja sai 4.8 tähden keskimäärin 19.5 käyttäjältä

Sivu 1/2
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
04-02-12
NU-CTS2
Cadillac CTS
Navigation Unlock
Integration Interface
Installation: Disconnect the black 44-pin main harness from the back of the radio (see g. A) Plug the male connector on the NU-CTS2
harness into the 44-pin port on the back of the radio. Connect the factory 44-pin harness into the female connector on the NU-CTS2 harness.
2008-2009 Vehicles Only: Locate the vehicles VSS wire in pin 20 of the gray 20-pin plug on the back of the radio (see g. A & B). This wire will
need to be cut then connected as follows: The green/black wire from the NU-CTS2 should be connected to the radio/plug side of the VSS wire
and the green/white wire from the NU-CTS2 should be connected to the vehicle side of the VSS wire.
The NU-CTS2 is a Navigation Unlock integration interface that allows the factory navigation features of
your Cadillac CTS radio or the reverse camera to be used by the passenger at anytime.
Main 44-pin Plug
Gray 20-pin Plug
Installation
Cadillac CTS Controls
Press & hold to
enable/disable
Navigation Unlock
1. Press & Hold the
Source Button
2. Information Center
Displays: Confirm
Safe Use
3. Press the Source
Button Again to
Confirm
4. Repeat Step 1
to De-Activate
Activating the Navigation Unlock
Cadillac CTS: Press and hold the “Source” button on the steering wheel controls (SWC) for two seconds to activate the NU-CTS2. You will hear
one chime and the driver information center on the instrument cluster will display “Conrm Safe Use”. Press the “Source” button on the SWC
again to acknowledge “safe use”, agreeing that use will be performed only by the passenger whenever the vehicle is in
motion, and activate the NU-CTS2. To de-activate the NU-CTS2 simply press and hold the “Source” button on the SWC until two chimes are
heard. The NU-CTS2 text will not be displayed when the OnStar Turn-by-Turn Navigation is being used.PLEASE NOTE:
Cadillac CTS-V: Make sure that both of the mirror control lights are off on the driver door. Press the Up button on the mirror controls to activate
the NU-CTS2. You will hear one chime and the driver information center on the instrument cluster will display “Conrm Safe Use”. Press the
Up button on the mirror controls again to acknowledge “safe use”, agreeing that use will be performed only by the passenger
whenever the vehicle is in motion, and activate the NU-CTS2. To de-activate the NU-CTS2 simply press the Up button on the mirror
control. The NU-CTS2 text will not be displayed when the OnStar Turn-by-Turn Navigation is being used.PLEASE NOTE:
WARNING: In order to avoid distraction, which could lead to an accident, the driver should never utilize systems unlocked by the NU-CTS2 when the
vehicle is in motion. Even when operated by the passenger, the vehicle driver should maintain their attention on the road at all times.
Operation
Pin 20
Cadillac CTS-V Controls
Press Once to
Enable/Disable
Navigation Unlock
Make Sure the Control
Lights Are O.
1. Turn o all
mirror controls
2. Press the
Up Button
2. Information Center
Displays: Confirm
Safe Use
3. Press the Up
Button Again to
Confirm
4. Repeat Step 2
to De-Activate

Tuotetiedot

Merkki: PAC
Kategoria: Ei luokiteltu
Malli: NU-CTS2

Tarvitsetko apua?

Jos tarvitset apua merkille PAC NU-CTS2 esitä kysymys alla ja muut käyttäjät vastaavat sinulle