Whirlpool WIS 7030 PEL Käyttöohje
Whirlpool
Astianpesukone
WIS 7030 PEL
Lue alta 📖 käyttöohje suomeksi merkille Whirlpool WIS 7030 PEL (35 sivua) kategoriassa Astianpesukone. Tämä opas oli hyödyllinen 9 henkilölle ja sai 4.7 tähden keskimäärin 5 käyttäjältä
Sivu 1/35
ENQuick Guide
1
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.whirlpool.eu/register
CONTROL PANEL
FIRST TIME USE
1. ON-OFF/Reset button with indicator light
2. Program selection button
3. Salt rell indicator light
4. Rinse Aid rell indicator light
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Multizone indicator lights
9. Multizone button
10. Delay button
11. Turbo button with indicator light
12. Power Clean button with
indicator light
13. START/Pause button with
indicator light / Tab
Before using the appliance carefully read the Safety Instruction.
PLEASE SCAN THE QR CODE ON YOUR
APPLIANCE IN ORDER TO HAVE MORE
DETAILED INFORMATION
1 2 3 4 5 6 7 8 9 10
11 12 13
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher and must be
lled when the SALT REFILL indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 1 kg); it is not unu-
sual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the proce-
dure before the beginning of the washing cycle to avoid corrosion.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse
aid dispenser A should be lled when the RINSE
AID REFILL indicator light in the control
panel is lit.
NEVER pour the rinse aid directly into the appliance
tub.
A
C
D
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce the
detergent into the dry dispenser D only. Place the amount of detergent for
pre-washing directly inside the tub.
If all-in-one detergents are used, we recommend using the TABLET button,
because it adjusts the program so that the best washing and drying results
are always achieved.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on heater, contributing also to better cleaning e-
ciency. This system regenerates itself with salt, therefore it is required
to rell salt container when empty.
Frequency of regeneration depends on water hardness level setting - regen-
eration takes place once per 6 Eco cycles with water hardness level set to 3.
Regeneration process starts in nal rinse and nishes in drying phase, be-
fore cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
Program Programs description
Drying
phase
NaturalDry
Available
options
*)
Duration
of wash
program
(h:min)
**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
1.
Eco 50°- Program is suitable to clean normally soiled tableware,
that for this use, it is the most ecient programme in terms of
its combined energy and water consumption, and that it is used
to assess compliance with the EU Ecodesign legislation.
3:10 9.5 0.85
2.
6
th
Sense® 50°- 60°- For normally soiled dishes with dried food
residues. Senses the level of soiling on the dishes and adjusts
the program accordingly.
1:25 - 3:00 7.0 - 14.0 0.90 - 1.40
3.
Intensive 65° - Program recommended for heavily soiled crock-
ery, especially suitable for pans and saucepans.
2:50 16.0 1.60
4.
Mixed 60°- Mixed soil. For normally soiled dishes with dried food
residues.
2:30 16.0 1.30
5.
Fast Wash&Dry 50° - Normally soiled crockery. Everyday cy-
cle, that ensures optimal cleaning and drying performance in
shorter time.
1:25 11.5 1.10
6.
Crystals 45° - Program for delicate items, which are more sensi-
tive to high temperatures, for example glasses and cups.
1:40 11.5 1.20
7.
Rapid 30’ 50° - Program to be used for half load of lightly-soiled
dishes with no dried food residues. Without drying.
- -
0:30 9.0 0.50
8.
Silent 50° - Suitable for night-time operation of the appliance.
With the lowest noise.
3:30 15.0 1.15
9.
Sanitizing 65°- Normally or heavily soiled crockery, with addi-
tional antibacterial wash. Can be used to perform maintenance
of the dishwasher
-
1:40 10.0 1.30
PROGRAMS TABLE
2
Quick GuideEN
TURBO - This option can be used to reduce the duration of the main
programs while maintaining the same washing and drying performance levels.
DELAY - The start time of the program may be delayed for a period of
time between 1 and 12 hours.
The DELAY function cannot be set once a wash cycle has been started.
POWER CLEAN® - Thanks to the additional power jets this option
provides a more intensive and powerful wash in the lower rack, in the
specic area. This option is recommended for washing pots and casseroles.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED ashes rapidly 3 times and beeps will sound. The option will not be enabled.
MULTIZONE - If there are not many dishes to be washed, a half load-
ing may be used in order to save water, electricity and detergent. By
default the appliance washes dishes in all racks.
OPERATION INDICATOR -
A LED light projected on the oor indicates
that the dishwasher is working.
One of the following operating modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds, stays o during
the cycle and ashes at the end of the cycle.
c) The light stays on during the cycle and ashes at the end of the cycle
(default mode).
Please scan the QR code on your product in order to have more detailed information.
NaturalDry is a convection drying system which automatically opens the
door during/after drying phase to ensure exceptional drying performance
every day. Door opens at the temperature that is safe to your kitchen furni-
ture, thus door will not be opened when the option of TURBO is on.
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@europeanappliances.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
Program Programs description
Drying
phase
NaturalDry
Available
options
*)
Duration
of wash
program
(h:min)
**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
10.
Prewash - Use to refresh crockery planned to be washed later.
No detergent to be used with this program.
- -
0:12 4.5 0.01
11.
Self- Clean 65°- Program to be used to perform maintenance
of the dishwasher, to be carried out only when the dishwash-
er is EMPTY using specic detergents designed for dishwasher
maintenance.
- -
0:50 8.0 0.85
LOADING THE RACKS
CAPACITY: 14 standard place-settings
CUTLERY RACK
(loading example for the cutlery rack)
The third rack was designed to house the cutlery.
The cutlery basket is equipped with two sliding side trays to make the most
of the height of the space below and enable the loading of high items into
upper rack.
UPPER RACK
(loading example for the upper rack)
Load delicate and light dishes: glasses, cups, saucers, low
salad bowls.
FOLDABLE
FLAPS WITH
ADJUSTABLE
POSITION
LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc.
Large plates and lids should ideally be placed
at the sides to avoid interferences with the
spray arm.
The lower rack has tip-up supports which can
be used in a vertical position when arranging
plates or in a horizontal position (lower) to
load pans and salad bowls easily.
(loading example for
the lower rack)
POWER CLEAN®
Power Clean® uses the special water jets in the rear
of cavity to wash more intensively the high dirty
items. The lower rack has a Space Zone, a special
pull-out support in the rear of the rack that can be
used to support frying pans or baking pans in up-
right position, thus taking up less space.
Placing the pots/casseroles faced to the Power Clean® component please
activate the POWER CLEAN® on the panel.
ENQuick Guide
3
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher does
not ll the water.
Display shows: H,
6 and On/O LED is
blinking rapidly
No water in the water supply or the tap is closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dish-
washer and reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it
After having carried out the verication and cleaning, turn o and turn on
the dishwasher and restart a new program.
Dishwasher nishes
the cycle prematurely.
Display shows: 15 and
On/O LED is blinking
rapidly
Drain hose positioned too low or siphoning
into home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve if
necessary.
Air in water supply. Check water supply for leaks or other issues letting air inside.
Detergent leaks.
Depends on the liquid detergent used and can be
emphasized in case of delay option is activated.
Small leaks will not cause machine malfunction and can be avoided by changing
liquid detergent type or using tablets.
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a
period of either up to 7 or up to 10 years, according to the specic Regulation requirements.
TROUBLESHOOTING
Please scan the QR code on your product in order to have more detailed information.
More information in the Daily Reference Guide on website.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY CLEANING THE SPRAY ARMS
A
A
B
C
In case you nd foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
The lower spray arm may
be removed by pulling it
upwards.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.whirlpool.eu/docs and parts-selfservice.europeanappliances.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identier that can be used to consult the portal of the registry
at https://eprel.ec.europa.eu.
IEC 436
:
®/TM/ © 2024 Whirlpool, Produced under license
Tuotetiedot
| Merkki: | Whirlpool |
| Kategoria: | Astianpesukone |
| Malli: | WIS 7030 PEL |
Tarvitsetko apua?
Jos tarvitset apua merkille Whirlpool WIS 7030 PEL esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Astianpesukone Whirlpool Käyttöohjeet
13 Helmikuuta 2025
6 Helmikuuta 2025
6 Helmikuuta 2025
6 Helmikuuta 2025
6 Helmikuuta 2025
18 Tammikuuta 2025
14 Tammikuuta 2025
14 Tammikuuta 2025
14 Tammikuuta 2025
14 Tammikuuta 2025
Astianpesukone Käyttöohjeet
- Astianpesukone Gorenje
- Astianpesukone Brandt
- Astianpesukone Elba
- Astianpesukone LG
- Astianpesukone Café
- Astianpesukone Sauber
- Astianpesukone ATAG
- Astianpesukone Technika
- Astianpesukone Miele
- Astianpesukone Balay
- Astianpesukone Prima
- Astianpesukone Kuppersbusch
- Astianpesukone Otsein
- Astianpesukone Privileg
- Astianpesukone Bompani
Viimeisimmät Astianpesukone Käyttöohjeet
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025