StarTech.com PEX1S953LP Käyttöohje
Sivut 2 Engels Ei luokiteltu
Lue käyttöohje merkille StarTech.com PEX1S953LP ilmaiseksi verkossa tai lataa PDF. Ohje on ollut hyödyllinen 39 henkilölle. Kysyttävää mallista? Esitä kysymys
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: February 7, 2019 10:23 AM
Product Diagram (PEX1S953LP)
PortFunction
1Serial Port• Used to connect a Serial Device
2Screws
• Used to attach the Serial Port to the Bracket
• Used to secure a Serial Cable to the Serial Port
3Bracket• Used to attach the Card to your Computer
4
PCI Express Bus
Connector
• Used to connect the PCI Express Serial Card to
your Computer’s Motherboard
5Jumper• Used to congure Serial Port power settings
6Printed Circuit Board
• Components such as Jumpers are located on
this Board
7LP4 Power Connector• Used to connect a Power Source
1-Port PCI Express Serial Card with 16950 UART - Low-Prole
Requirements
• PCIe Slot
• Needle-Nose Pliers
For the latest requirements and full manual, please visit
www.startech.com/PEX1S953LP.
Installation
WARNING!
PCI Express Serial Cards can be severely damaged by static electricity. Make sure
that you are properly grounded before you open your or touch the Computer Case
PCI Express Serial CardAnti-Static Strap. You should wear an when you install any
computer component. If an isn’t available, discharge any built-up Anti-Static Strap
static electricity by touching a large for several seconds. Only Grounded Metal Surface
handle the by its edges and don’t touch the gold connectors.PCI Express Serial Card
Jumper Conguration
Note: Jumper Serial Devices conguration is a requirement when connecting that
require power through a . Serial Port
This can be moved into one of three dierent positions in order to set the Jumper
power output voltage for the . The default setting for the is , Serial PortJumpersRI
which is the setting for no power. The can be moved to one of the other two Jumper
settings for or of power. To congure the , complete the following:5V12VJumper
1. Determine the power setting that is required for the .Serial Port
2. Locate the . The is labeled as on the .JumperJumperJ1Printed Circuit Board
3. Carefully remove the . Lift the straight up and o of the JumperJumper PCI Express
Serial Card.
Note: Always hold the by the edges.Card
4. Position the over the set of that correspond with the desired JumperPinsSerial
Port Power SettingJumper. See to determine where the Figure 1 should be
positioned.
5. Push the straight down and into place.Jumper
Note: Push theall the way into position for proper contact. Jumper
1
4
7
5
6
2
3
Tuotetiedot
| Merkki: | StarTech.com |
| Kategoria: | Ei luokiteltu |
| Malli: | PEX1S953LP |
Tarvitsetko apua?
Jos tarvitset apua merkille StarTech.com PEX1S953LP esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Ei luokiteltu StarTech.com Käyttöohjeet
StarTech.com PCI2S950DV Käyttöohje StarTech.com PCI8S950LP Käyttöohje StarTech.com PEX16S550LP Käyttöohje StarTech.com PCIX1PEX4 Käyttöohje StarTech.com PEX1S1P952 Käyttöohje StarTech.com PEX1S1PMINI Käyttöohje StarTech.com PEX1S952LP Käyttöohje StarTech.com 21050-PC-SERIAL-LP Käyttöohje
Suosittuja kategoriassa Ei luokiteltu
StarTech.com 1P1FFC-USB-SERIAL Käyttöohje StarTech.com PEX4SFF8643 Käyttöohje StarTech.com PIB2S31 Käyttöohje