Satco S11969 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Satco S11969 (4 sivua) kategoriassa Monitor. Tämä opas oli hyödyllinen 28 henkilölle ja sai 4.8 tähden keskimäärin 14.5 käyttäjältä
Sivu 1/4
Satco Products, Inc.
Brentwood, NY 11717© Copyright 2022 Satco Products, Inc. 3/22 v4.0
1
CCT SELECTABLE LED
LINEAR T8 TYPE B LAMPS
Models: S11919, S11929, S11969
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
WARNING:
• DANGER: Risk of shock-disconnect power before
installation.
• WARNING: Risk of re or electric shock. LED
Retrot Kit installation requires knowledge of luminaire
electrical systems. If not qualied, do not attempt
installation. Contact a qualied electrician.
• WARNING: Product must be installed in accordance
with the national electrical code or your local electrical
code. If you are not familiar with these codes and
requirements, contact a qualied electrician.
• WARNING: Install this kit only in luminaries that have
the construction features and dimensions shown in the
photographs and/or drawing and where the input rating
of the retrot kit does not exceed the input rating of
the luminaire.
• WARNING: To prevent wiring damage or abrasion,
do not expose wiring to edges of sheet metal or other
sharp objects.
• WARNING: NOTE: Shunted lamp holders are found
only in uorescent luminaries with instant-start
ballasts. Instant-start ballasts can be identied by the
words “Instant Start” or “I.S.” marked on the ballast.
This designation may be in the form of a statement
pertaining to the ballast itself, or may be combined
with the marking for the lamps with which the ballast
is intended to be used, for example F40T 12/IS, for
more information contact the LED luminaire retrot kit
manufacturer.
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
Installers should not disconnect the existing wire from
lampholder terminals to make new connections at
lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder
and make new electrical connections to lampholder
lead wires by employing applicable connectors.
• WARNING: Luminaire wiring and electrical parts
may be damages when installing retrot kit hardware.
Check for enclosed wiring and components.
• WARNING: Check the existing wiring for damage
before installing upgrade kit. Do not install if existing
wires are damaged.
This retrot kit is accepted as a component of a
luminaire where the suitability of the combination shall
be determined by authorities having jurisdiction.
THIS RETROFIT KIT INCLUDES, LED TUBE,
OPERATING INSTRUCTIONS, AND FIXTURE LABEL
FOR THE DOUBLE OR SINGLE ENDED APPLICATION.
• “This luminaire has been modied and can no longer
operate the originally intended lamp,” shall be marked
on the retrot luminaire where readily visible by the user
during normal maintenance including lamping.
• Do not use with dimmers.
• Suitable for damp locations.
• Suitable for use in enclosed luminaries, not vapor tight.
• Suitable for use with the following emergency
equipment; SATCO Products, Inc., model S8000,
S8002; 5Watt or 10 Watt Emergency LED Driver.
• This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
Item
Number
Description
CCT Watts Hours Lumens
Minimum Lamp
Compartment Dimensions
(Length x Width x Height)
Lamp-to-Lamp
Spacing
S11919 12.5T8/LED/48/840-850-865/BP/2PK
40-50-65K
12.5W 50,000 1800
47 7/8 x 23 7/8 x 4 inches
(121.5 x 60.5 x 10 cm)
4 3/8 inches
(11cm)
S11929 12.5T8/LED/48/840-850-865/BP
S11969 12.5T8/LED/48/830-835-840/BP 30-35-40K
The units covered by this report were intended to retrot surface mount, Type IC or non-IC recessed mount Listed uorescent
luminaires that use maximum 4 tubular lamps, the minimum lamp compartment dimensions are tabulated below.
Tuotetiedot
| Merkki: | Satco |
| Kategoria: | Monitor |
| Malli: | S11969 |
Tarvitsetko apua?
Jos tarvitset apua merkille Satco S11969 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Monitor Satco Käyttöohjeet
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
Monitor Käyttöohjeet
- Monitor HP
- Monitor EMOS
- Monitor BenQ
- Monitor Gigabyte
- Monitor Posiflex
- Monitor Antelope Audio
- Monitor Soundstream
- Monitor HoverCam
- Monitor BookIT
- Monitor Ikan
- Monitor AVer
- Monitor Ernitec
- Monitor Desview
- Monitor Bearware
- Monitor Asrock
Viimeisimmät Monitor Käyttöohjeet
8 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
7 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
2 Huhtikuuta 2025
1 Huhtikuuta 2025
30 Maaliskuuta 2025
29 Maaliskuuta 2025