Privileg PV2IC10BS7LA0 Käyttöohje

Privileg Astianpesukone PV2IC10BS7LA0

Lue alta 📖 käyttöohje suomeksi merkille Privileg PV2IC10BS7LA0 (8 sivua) kategoriassa Astianpesukone. Tämä opas oli hyödyllinen 33 henkilölle ja sai 4.7 tähden keskimäärin 17 käyttäjältä

Lataa PDF

Sivu 1/8

ENQuick Guide

PROGRAMS TABLE

Program Programs description

Drying

phase

Auto Door

Available

options

Duration

ofwash

program

(h:min)

**)

Water

con-

sumption

(litres/cycle)

Energy

con-

sumption

(kWh/cycle)

Eco 50°- Eco program is suitable to clean normally soiled tableware, that

for this use, it is the most ecient program in terms of its combined energy

and water consumption, and that it is used to assess compliance with the EU

Ecodesign legislation.

3:35 8.7 0.59

Auto Intensive 65° - Automatic program for heavily soiled dishes and pans

(not to be used for delicate items).

2:00 - 3:10 14.0 - 17.0 1.50 - 1.85

Auto Mixed - 55° Automatic program for normally soiled pans and dishes.

1:20 - 3:00 7.0 - 14.0 0.70 - 1.10

Half Load 55°- Ideal for washing a half load of lightly or normally soiled crockery.

1:20 11.0 1.00

Rapid 30’ 45° - Program to be used for half load of lightly-soiled dishes with

no dried food residues. Without drying.

0:30 9.0 0.50

Extra Hygiene 65° - Normally or heavily soiled crockery, with additional antibac-

terial wash. Can be used to perform maintenance of the dishwasher.

1:50 12.0 1.30

Extra - 50° Program that allows to wash very big items loaded in the lower

rack. Please apply detergent directly to tub instead of detergent dispenser.

Upper rack should be removed with this cycle.

1:30 11.0 1.20

Prewash - Use to refresh crockery planned to be washed later. Nodetergent

to be used with this program.

0:10 4.5 0.01

Push&GO 50° - Everyday wash and dry cycle that ensures great cleaning per-

formance in a short time without the need to pre-treat dishes.

1:25 11.5 1.10

1. On-O/Reset button with indicator

light

2. Program selection button

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program number and delay time

indicator

6. Tablet (Tab) indicator light

7. Display

8. Push & Go button

9. Delay button

10. Start/Pause button with

indicator light/ Tablet (Tab)

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and on

the machine’s functional components.

• It is mandatory that the salt reservoir never be empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher and must be

lled when the SALT REFILL indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Position the funnel and ll the salt reservoir (see gure)

right up to its edge (approximately 1 kg); it is not unu-

sual for a little water to leak out.

3. Only the rst time you do this: ll the salt reservoir

with water.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get into the

container during the wash program (this could damage the water softener be-

yond repair). Whenever you need to add salt, it is mandatory to complete the

procedure before the beginning of the washing cycle to avoid corrosion.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently pre-

venting scale buildup on heater, contributing also to better cleaning e-

ciency. This system regenerates itself with salt, therefore it is required

to rell salt container when empty.

Frequency of regeneration depends on water hardness level setting - regen-

eration takes place once per 6 Eco cycles with water hardness level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase, be-

fore cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse

aid dispenser should be lled when the A RINSE

AID REFILL indicator light in the control pan-

el is lit. NEVER pour the rinse aid directly into the

appliance tub.

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device . Introduce the C

detergent into the dry dispenser only. Place the amount of detergent for D

pre-washing directly inside the tub.

If all-in-one detergents are used, we recommend using the TABLET button,

because it adjusts the program so that the best washing and drying results

are always achieved.

Usage of detergent not designed for dishwashers may cause malfunc-

tion or damage to the appliance.

1 2 3 4 5 6 7 8 9 10

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories: For information on

comparative EN testing conditions, please send an email to the following address:

dw_test_support@europeanappliances.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and

pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-

bration. The sensor calibration can increase program duration up to 20 min.

PLEASE SCAN THE

QR CODE ON YOUR

APPLIANCE IN

ORDER TO HAVE

MORE DETAILED

INFORMATION

Before using the appliance carefully read Safety and Installation Instructions.

After installation, please remember to remove all transport protection parts from

the dishwasher.

CONTROL PANEL

FIRST TIME USE