Parkside PWSZS 1 Käyttöohje
Parkside
Ei luokiteltu
PWSZS 1
Lue alta 📖 käyttöohje suomeksi merkille Parkside PWSZS 1 (2 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 33 henkilölle ja sai 4.5 tähden keskimäärin 17 käyttäjältä
Sivu 1/2
1 2 3 4 5
KEEP ALL SAFETY NOTES AND
INSTRUCTIONS FOR FUTURE
REFERENCE!
General information about
grinding tools and their
properties
• Grinding tools are fragile there-
fore utmost care must be taken
when handling grinding tools.
• Using damaged, incorrectly
clamped or installed grinding
tools is dangerous and can lead
to serious injuries.
Selection of grinding tools
for safe and proper use
• Details on the label or the grind-
ing tool and restrictions on use,
safety instructions and further
information must be observed.
Handling and storage of
grinding tools
• Grinding tools must be handled
and transported carefully.
• Grinding tools must be stored so
that they are not exposed to any
mechanical damage or harmful
environmental influences. (for ex-
ample moisture).
Conditions to be met prior
to using the grinding tools
• Grinding tools must be visually
inspected prior to each commis-
sioning.
• Continuing to use damaged
grinding tools is not permitted.
• Grinding tools must not be
mounted on to machines which
have a rotation speed above the
highest permitted rotation speed
of the brushes or the grinding
tool.
Instructions for clamping
• Grinding tools must be clamped
in accordance with the instruc-
tions of the grinding tool and ma-
chine manufacturer.
• After completing each clamping
procedure, perform a test run
for a suitable period of time. The
labelled maximum working speed
(rotational speed) of the grinding
tool is not permitted to be ex-
ceeded during this.
Operating and Safety Instructions for
Diamond Cutting Disc Set/Wire Cup Brush/
Cutting Disc Set/Cutting/Grinding Disc Set
WARNING! To reduce the risk of injury. Please read the
operating & safety instructions carefully before initial com-
missioning of the grinding tool. These operating & safety in-
structions must also be passed on to other users.
Grinding operation (and/
or cut-off grinding opera-
tion if applicable)
• Follow the user information from
the machine manufacturer.
• Affix all protective equipment to
the machine before commission-
ing.
• Do not perform any work without
using protective equipment to se-
cure everything.
• Use personal protective equip-
ment in accordance with the type
of machine and application, for
example safety goggles and
visors, hearing protectors, res-
piratory protection, safety shoes,
protective gloves and other pro-
tective clothing.
• Only perform grinding operations
for which the grinding tool is
suitable, in accordance with the
labelling (take restrictions for use,
safety instructions or other infor-
mation into account for this).
• Switch off the hand-operated
grinding machine before laying
it on the floor or the workbench
and wait for the device to stop.
Safety notes for all appli-
cations
General safety instructions
on grinding and cut-off
grinding:
Do not use accessories that have
not been designed and recom-
mended by the manufacturer for
use with this power tool. Just be-
cause you are able to attach an
accessory to your power tool this
does not guarantee that it is safe to
use.
The permitted revolutions of the
tool must be at least as high as the
highest revolutions specified on the
power tool. Accessories that rotate
faster than they are permitted to
may break and fly.
Grinding discs, flanges or other
accessories must fit precisely onto
the grinding spindle of your power
tool.
Do not use damaged insertion
tools.
Check the insertion tools as well as
grinding discs for splintering and
cracks prior to each use.
Ensure that other people are kept
at a safe distance to the area in
which you are working.
Anyone entering the workplace
must wear personal protective
equipment. Pieces of the work
piece or broken tools may fly away
and cause injuries even outside the
direct working area.
Never set the power tool down be-
fore the insertion tool has come to
a complete standstill.
The rotating tool may come into
contact with the surface and cause
you to lose control over the power
tool.
Never operate the power tool
while you are carrying it. Your
clothing may be caught as a result
of accidental contact with the rotat-
ing tool causing the tool to injure
you.
Never use the power tool in the vi-
cinity of flammable materials.
Sparks may set fire to these mate-
rials.
Additional safety notes for
all applications
Kickback and appropriate
safety notes
Kickback is a sudden reaction
caused as a result of a jammed
or blocked rotating insertion tool
(grinding disc).
A kickback is a consequence of
incorrect or faulty operation of the
power tool. It can be prevented by
the use of suitable measures, as de-
scribed below:
Hold the electrical tool securely
with both hands and position your
body and arms in such a way that
you are able to absorb any kick-
back. Always use an additional
handle, if available, to ensure you
have the greatest possible level of
control over the kickback forces or
reaction torque when starting up.
Never bring you hand close to the
rotating insertion tool.
Position your body in such a way
that it is not located where the
power tool is likely to kickback to.
Be especially careful around cor-
ners, sharp edges etc. Prevent in-
sertion tools from bouncing off the
workpiece and becoming jammed.
The rotating insertion tool tends to
become jammed at corners, sharp
edges or when it bounces.
This will lead to a loss of control or
kickback.
Additional safety instruc-
tions for diamond cutting
discs:
• Only for cutting! Not for rough-
ing!
• Not suitable for metal! Danger of
injury! Cutting and cooling
• Diamond cutting discs must al-
ways be installed without lateral
and radial runout
• Do not move backwards and for-
wards within the material, draw
through steadily instead
• To prevent the risk of cracks in the
centre or segment breaks- only
work at a right angle and in a
straight line.
• Do not apply too much grinding
pressure; the weight of the ma-
chine is sufficient
• When using diamond cutting
discs, make sure to leave an ap-
propriate amount of time for cool-
ing.
• These may vary depending on
the cutting capacity, type of
cutting and material being pro-
cessed; therefore, the user must
make sufficient time for cooling
and take the various factors into
account.
• Caution! The diamond cutting
disc gets very hot during work;
only handle them with protective
gloves.
Additional safety instruc-
tions on grinding and cut-
off grinding
Use only grinding tools expressly
permitted for use with your power
tool and the appropriate protective
hood for these grinding tools.
The protective hood must be af-
fixed securely to the power tool
and set in such a way that it en-
sures the maximum level of safety
possible, i.e. the smallest possible
area of the grinding tool is ex-
posed to the operator.
Grinding tools may only be used
for the recommended applications.
For example:
Never sand using the side surface
of a cutting wheel.
Always use undamaged tension-
ing flanges in the correct size and
shape for the grinding disc you
have selected.
Additional safety instruc-
tions on cut-off grinding
Avoid blocking the cutting disc or
employing too great a pressure.
Do not carry out any excessively
deep cuts.
Avoid the area in front and behind
the rotating cutting disc.
If the cutting disc blocks or you
stop working, switch the unit off
and hold it still until the disc has
come to a standstill. Never attempt
to pull a still operating cutting disc
out of the cut as this may cause
kickback.
Do not switch the power tool back
on with it still in the workpiece.
Allow the cutting disc to achieve
the full revolutions before you con-
tinue to cut carefully.
Support boards or large work-
pieces to reduce the risk of kick-
back caused by a jammed cutting
disc.
Be particularly careful when car-
rying out “plunge cuts” into an
existing wall or an area you can’t
see into.
Cleaning and maintenance
Never use any aggressive or abra-
sive cleaning materials. Otherwise
the surface of the product can get
damaged. The product must always
be clean, dry and free from oil or
lubricating greases. Use a slightly
damp, lint-free cloth for cleaning.
Service
Conmetall Meister GmbH
Oberkamper Str. 39
42349 Wuppertal - Germany
GERMANY
Email: meister-service@
conmetallmeister.de
Disposal
The packaging is made up of en-
vironmentally friendly materials
which may be disposed of via your
local recycling points.
Options for the disposal of the used
product can be obtained from your
community or city administration.
Contents and the meaning
of labelling and enclosed
information
Not permitted for hand-held
and manual grinding
Only for roughing/Only for
grinding
Not for roughing
Only for cutting
Not for cutting
Do not use for processing
metal
Not permitted for wet grind-
ing
Not permitted for side grind-
ing
Do not use if damaged
Only permitted in conjunction
with a support plate
Only permitted for wet cutting
Follow safety recommenda-
tions
Use safety goggles
Wear a safety helmet
Use hearing protectors
Use gloves
Put on a dust mask
Unplug from the power
source
is a registered trademark of
Conmetall Meister GmbH ·
42349 Wuppertal, Germany
Store these safety instructions in a
safe place.
Note on marking on the disc
flange:
The format is: MM/YYYY
PD 11/21 = production date
EXP 02/24 = expiry date
EXP only valid for cutting discs/
grinding discs and flap discs
6
IAN 373556_2104
Conmetall Meister GmbH
Oberkamper Str. 39
42349 Wuppertal · DEUTSCHLAND
E-Mail: meister-service@conmetallmeister.de
Imported for GB market by:
Lidl Great Britain Ltd, Lidl House,
14 Kingston Road, Surbiton, KT5 9NU
Latest information ∙ Informationsstatus
Mise à jour des informations ∙ status van
de informatie : 06/2021
Nr. WU5455611-8
Tuotetiedot
| Merkki: | Parkside |
| Kategoria: | Ei luokiteltu |
| Malli: | PWSZS 1 |
Tarvitsetko apua?
Jos tarvitset apua merkille Parkside PWSZS 1 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Ei luokiteltu Parkside Käyttöohjeet
10 Maaliskuuta 2025
10 Maaliskuuta 2025
10 Maaliskuuta 2025
10 Maaliskuuta 2025
10 Maaliskuuta 2025
10 Maaliskuuta 2025
5 Maaliskuuta 2025
11 Tammikuuta 2025
11 Tammikuuta 2025
29 Joulukuuta 2024
Ei luokiteltu Käyttöohjeet
- Ei luokiteltu WilTec
- Ei luokiteltu Noxon
- Ei luokiteltu Moulinex
- Ei luokiteltu Physa
- Ei luokiteltu Rotatrim
- Ei luokiteltu Thermador
- Ei luokiteltu Nexa
- Ei luokiteltu CELLFAST
- Ei luokiteltu Crem
- Ei luokiteltu Furman
- Ei luokiteltu Bebob
- Ei luokiteltu YSI
- Ei luokiteltu Haeger
- Ei luokiteltu MOZA
- Ei luokiteltu Conair
Viimeisimmät Ei luokiteltu Käyttöohjeet
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025