OSD Audio IWS-88 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille OSD Audio IWS-88 (2 sivua) kategoriassa Subwoofer. Tämä opas oli hyödyllinen 18 henkilölle ja sai 5.0 tähden keskimäärin 9.5 käyttäjältä
Sivu 1/2
18AWG minimum - for distances up to ………………………. . 10 ft
16AWG - from ……………………………………………. 10 to 50 ft
14AWG - from …………………………………………… 50 to 100ft
- Where is the best place to install the speakers
- Where do the speakers sound the best
- When placing the speakers in the wall, try to locate them so that the
sound is projected towards the general listening area.
- If you intend to paint the grilles, try to do so before installation.
Quick installation guide
- Pencil
- Drill
- Tape Measure
- Wire cutter
- Philips-head screwdriver
- Sandpaper
Tools needed for installation
STEP 1
Trace along the inclusive template. Cut along the traced line using a
drywall saw or rotary drill. A simple, inexpensive drywall saw (about
$10 at your local hardware store) is the best choice for beginners.
Caution: This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the
desired mounting area, you should start by cutting a small hole in
the center of your penciled mounting hole with a drywall saw. Use a
piece of sandpaper to sand down the cut out edge for a smoother
contour. (See Diagram 1 and Diagram 2)
Run the cable into the cut out location while leaving an extra two
feet to make the connection to the speaker easier. St
STEP 2
rip back
approximately ½” of the speaker cable insulation and twist
the copper wires tightly for easy insertion.
On the back of the speaker, press down on the gold-plated
compression terminal to reveal the "eye" and insert the speaker
cable through the eye for secure connection. Release the compres-
sion terminal to lock each cable securely.
Diagram 1:
Cutout tracing
Diagram 2:
Cut Out
To determine the length and the gauge of speaker wire, you will need to
measure the distance between your receiver/amplifier and the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
- Utility knife
- Safety eyewear
- Gloves
Speaker wire
- -
- Measure the distance from the receiver/amplifier to the speakers.
-----------------
----------------
-----------------
-----------------
----------------
-----------------
STEP 3
Tighten the dog-ear brackets by simply turning the screws on the
slowly clockwise. The quick-turn mounting system and frame will
"sandwich" or clamp around the wall to hold the speaker securely in
place. (See Diagram 3)
Diagram 3:
Mounting Dog Ear
Closed
Loose
Closed
L
oose
..... ......
..
.
.
.
.
.
......
.
dog ear
STEP 4
Screw
Screw
Screw
Screw
Tighten the four mounting screws with the same amount of force until
the speaker is aligned and held securely to the wall surface. Caution:
do not over tighten! (See Diagram 4)
Diagram 4:
MANUAL
DUAL 8" IN-WALL
S U B W O O F E R
IWS88
Tuotetiedot
| Merkki: | OSD Audio |
| Kategoria: | Subwoofer |
| Malli: | IWS-88 |
Tarvitsetko apua?
Jos tarvitset apua merkille OSD Audio IWS-88 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Subwoofer OSD Audio Käyttöohjeet
28 Tammikuuta 2025
28 Tammikuuta 2025
4 Tammikuuta 2025
3 Tammikuuta 2025
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
Subwoofer Käyttöohjeet
- Subwoofer Dynacord
- Subwoofer SoundTube
- Subwoofer Martin Audio
- Subwoofer Deaf Bonce
- Subwoofer Vonyx
- Subwoofer Indiana Line
- Subwoofer Eve Audio
- Subwoofer Ecler
- Subwoofer PSB
- Subwoofer Monitor Audio
- Subwoofer Yorkville
- Subwoofer ButtKicker
- Subwoofer Apart
- Subwoofer Nubert
- Subwoofer Teufel
Viimeisimmät Subwoofer Käyttöohjeet
4 Huhtikuuta 2025
2 Huhtikuuta 2025
1 Huhtikuuta 2025
30 Maaliskuuta 2025
19 Maaliskuuta 2025
19 Maaliskuuta 2025
19 Maaliskuuta 2025
19 Maaliskuuta 2025
19 Maaliskuuta 2025
19 Maaliskuuta 2025