Oliveri VE402CR Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Oliveri VE402CR (10 sivua) kategoriassa anturi. Tämä opas oli hyödyllinen 33 henkilölle ja sai 4.5 tähden keskimäärin 17 käyttäjältä
Sivu 1/10
HOB MOUNT SENSOR TAP
VE402CR/VE402MB
CARE & MAINTENANCE
Clean with a soft cloth and warm soapy water as necessary - rinse and dry after cleaning. Under No Circumstances
should abrasive or acid based cleaning products be used
WARRANTY
This warranty does not cover against normal wear and will be voided if the product is misused or
not installed in accordance with these instructions.
In the event this product is rendered obsolete and a replacement product is required, Oliveri Solutions Pty Ltd
reserves the right to supply a product of equal substitution at their discretion.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
SERVICE
If the problem represents a danger, or damage to property may occur, immediately shut off the water
supply. If the tap requires servicing, please contact your plumber (preferably the one who installed
it). Most problems occur due to contaminated supply lines or water pressure exceeding 500KPa.
Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure.
If the Plumber is satisfied that the problem is not due to poor installation, contact T2 Services Pty Ltd for
assistance on:
Ph: (07) 5596 0738
Fax: (07) 5527 3353
Email: https: //oliveri.com.au/service-and-warranty
If a warranty service agent finds that the tap is not at fault, T2 Services Pty Ltd reserves the right to
pass on any callout fee to the householder.
THIS SENSOR TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN
ACCORDANCE WITH LOCAL REGULATIONS
This Oliveri sensor tap is manufactured to standard AS/NZS 3718.
Technical Data
Installation Instructions
VE402CR/VE402MB installation instructions.pdfIssue Date 08/08/2020 Revision Number: V1.0
MAX OPERATING PRESSURE.............................................................5 bar (500kPa)
RECOMMENDED OPERATION PRESSURE........................................1.5-5 bar (150-500kPa)
MAX HOT WATER TEMPERATURE .....................................................55°C
RECOMMENDED HOT WATER TEMPERATURE.................................50°C
Where water pressure exceeds 500kPa, a pressure reducing device is required to be installed.
Note that water pressure overnight can reach 150% of the daytime pressure
Before attempting any work involving mains water supply lines, ensure the water supply is shut off.
Stop valves (preferably with filters) must be used when installing your Oliveri tap to allow isolation.
Failure to do so where required will void warranty.
This sensor tap must be installed in accordance with these instructions.
Oliveri warrant that the sensor tap will be leak-free and drip-free for 5 years under normal use, and the Product’s
control box (which houses the hydraulic system) and finish will be free from defects in material and
manufacturing workmanship (but only so long as the Original Consumer/Commercial Purchaser continues to own
the dwelling or premises).
The warranty on all other components of the Product, including but not limited to the electronics box, spout and
lenses, runs for: (1) five years from the date of purchase for an Original Purchaser; or (2) one year from date of
purchase for an Original Commercial Purchaser (but only so long as the Original Consumer/Commercial
Purchaser continues to own the dwelling or premises).
Tuotetiedot
| Merkki: | Oliveri |
| Kategoria: | anturi |
| Malli: | VE402CR |
Tarvitsetko apua?
Jos tarvitset apua merkille Oliveri VE402CR esitä kysymys alla ja muut käyttäjät vastaavat sinulle
anturi Oliveri Käyttöohjeet
3 Huhtikuuta 2025
anturi Käyttöohjeet
- anturi IFM
- anturi Festo
- anturi Panasonic
- anturi Chauvin Arnoux
- anturi Moen
- anturi Hikvision
- anturi Jung
- anturi Crestron
- anturi Sensirion
- anturi Carrier
- anturi Metz Connect
Viimeisimmät anturi Käyttöohjeet
1 Huhtikuuta 2025
1 Huhtikuuta 2025
1 Huhtikuuta 2025
4 Helmikuuta 2025
31 Tammikuuta 2025
29 Joulukuuta 2024
22 Joulukuuta 2024
19 Joulukuuta 2024
19 Joulukuuta 2024
19 Joulukuuta 2024