NUVO SF77/196 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille NUVO SF77/196 (2 sivua) kategoriassa Helpotus. Tämä opas oli hyödyllinen 24 henkilölle ja sai 4.6 tähden keskimäärin 12.5 käyttäjältä
Sivu 1/2
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE
CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow the
steps in the order given. Under no circumstances should a xture be hung
on house electrical wires, nor should a swag type xture be installed on
a ceiling which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualied
electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts are
included as shown in gure. Be careful not to misplace any of the screws
or parts, which are needed to install this xture.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Position the back plate (B) through the xing holes onto the wall
and make marks, drill pilot holes for wood screws (C) into the wall, then
insert the plastic anchor (A) into the holes.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised
dimples on the mounting bar. Wrap the ground wire from the xture
(if supplied) around the green grounding screw, then connect it to ground
wire from the outlet box (if not xed on the outlet box) using a wire
connector (not supplied). If ground wire from the xture is not supplied,
wrap the ground wire (if not xed on the outlet box) from the outlet box
around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify which
group your xture wire(s) falls into and connect the wires according to the
directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square
shaped or ridged and the less tracer wire is round in shape or smooth (seen
best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against the
black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again for
a rm connection.
STEP 6: Connect the xture wire from group B to the white wire from
the outlet box in the same manner. Make sure no bare wires can be seen
outside wire connectors.
ITEM NO: SF77-188, SF77-189, SF77-190, SF77-191,
SF77-192, SF77-193, SF77-194, SF77-195, SF77-196
ARTÍCULO Nº: SF77-188, SF77-189, SF77-190, SF77-191,
SF77-192, SF77-193, SF77-194, SF77-195, SF77-196
ARTICLE N°: SF77-188, SF77-189, SF77-190, SF77-191,
SF77-192, SF77-193, SF77-194, SF77-195, SF77-196
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet box.
Secure back plate (B) to outlet box with outlet screws (D), then secure the
outlet box with wood screws (C) into plastic anchors (A) in the wall.
STEP 2: Place the front plate (F) over the sockets (E) and back plate (B)
to the wall.
STEP 3: Place the cups (G) over the sockets (E) to the front plate (F).
STEP 4: Install lamps (not supplied). Do not exceed the maximum capacity
recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration when
ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
Tuotetiedot
| Merkki: | NUVO |
| Kategoria: | Helpotus |
| Malli: | SF77/196 |
Tarvitsetko apua?
Jos tarvitset apua merkille NUVO SF77/196 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Helpotus NUVO Käyttöohjeet
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
4 Huhtikuuta 2025
Helpotus Käyttöohjeet
- Helpotus Bresser
- Helpotus Astera
- Helpotus Novy
- Helpotus Kogan
- Helpotus Media-tech
- Helpotus Hazet
- Helpotus Smith-Victor
- Helpotus Qazqa
- Helpotus Hama
- Helpotus Osram
- Helpotus Westinghouse
- Helpotus Govee
- Helpotus Showtec
- Helpotus Hudson Valley
- Helpotus Eglo
Viimeisimmät Helpotus Käyttöohjeet
9 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
7 Huhtikuuta 2025
5 Huhtikuuta 2025
5 Huhtikuuta 2025
5 Huhtikuuta 2025
5 Huhtikuuta 2025