Nubert nuLine RS-54 Käyttöohje

Nubert Kaiutin nuLine RS-54

Lue alta 📖 käyttöohje suomeksi merkille Nubert nuLine RS-54 (8 sivua) kategoriassa Kaiutin. Tämä opas oli hyödyllinen 6 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/8

nuLine RS-54

CERTIFIED

Compact Speaker

Rear Speaker

Dolby Atmos® Enabled

up-ﬁring speaker

Safety instructions

Operating manual

Technical data

Warranty terms

Thank you very much for choosing

Nubert loudspeakers.

You will be able to set up your system

without any problems if you read these

operating instructions carefully.

We will explain the operation, connection

and installation so that you can achieve

optimum sound quality and fully enjoy

your new speakers!

The Nubert team wishes you

happy listening!

Mounting the Speaker Grille

First, mount the spacers on the grille (see the separate grille mount-

ing instructions!), then carefully mount the grille on the speaker by

lining up the spacers of the grille with the matching rubber receivers

on the loudspeaker and pushing the grille in place. Be careful not to

scratch the speaker!

Licensing information:

Manufactured under license from Dolby Laboratories.

Dolby, Dolby Atmos, and the “double-D“ symbol are

trademarks of Dolby Laboratories.

Low Temperatures and Sound

When speakers are shipped and delivered during the cold months

of the year, it is imperative that they adapt to the temperature of

the living area. Low temperatures have a considerable inuence on

the moving parts of a loudspeaker such as diaphragm, voice coil,

bead and spider. The ability of these components to follow rapid

oscillations or to perform large excursions is thus signicantly re-

stricted. This is not dangerous, but “frozen” speakers are far from

their acoustic peak.

Hence our tip: When your new speakers arrive on a cold winter’s

day, just give them a few hours to acclimatise. Your Nubert speakers

will thank you with the superior sound quality you have come to

expect from us.

Safety Instructions

• Turn off your amplier before connecting the speaker cables

• Make sure the speaker cables are rmly attached

• Place the speaker in a dry location

• Do not place the speaker in direct sunlight

• -Overload protection: the nuLine RS-54 has an internal automa

tic overload protection fuse, but please be aware that small am-

pliers can damage your speakers too. At high sound pressure

levels, small ampliers can start to distort which can damage the

tweeters. If the speakers begin to sound harsh or distorted, turn

down the amplier to avoid damage to your speakers.

Elastic Bumpers (bumpons)

The bumpons provide rm, no-slip footing for your speakers and do

not leave marks or dents.

Do not mount the adhesive elastic bumpers until you are certain

you want to keep the speakers. The supplied brand-name bumpers

use a strong adhesive and are difcult to remove, especially if they

have been attached to the loudspeaker for a longer period of time.

If you wish to remove them, warm them up with a hairdryer or

similar before removing them carefully.

Whether you should use the larger or the smaller bumpers de-

pends on the application. Please see page 4 “Setup”.

Unpacking and Scope of Delivery

Unpacking

When unpacking your speaker, do not use sharp or pointed ob-

jects to avoid possible damage to the enclosure. Please keep the

packaging in a safe place in case you need to transport the speak-

er at a later date.

Scope of Delivery

If the delivery is complete, it contains the following parts:

• 2 speakers

• 2 metal grilles with mounting kit

• 2 loudspeaker cables 0,75 mm

2 (consider these as „backup“-

cables in case you want to get started and don‘t have any

speaker cables)

• 8 large adhesive bumpers

• 8 small adhesive bumpers

nuLine RS-54 · 09/2020 EN

Connections

Please make sure that your amplier/receiver is switched off

before connecting your speakers. For how to connect the speak-

ers to the amplier/receiver, please refer to the equipment‘s user

manual.

Terminal

You will nd the terminal for the speaker cable on the rear of the

speaker (when used in reective mode). The terminal has two bind-

ing posts, one with a red marking for plus and one with a black

marking for minus. Always make sure that plus on the loudspeaker

is connected to plus on the amplier and minus on the loudspeaker

to minus on the amplier. Reversing polarity will not harm your equip-

ment in any way, but the sound will be diffuse and bass-response

and imaging will be very poor. Most loudspeaker cables are marked

to make it easy to discern between plus and minus.

If you want to connect the speaker cable directly without any con-

nectors, remove 8 – 15mm of insulation from the end of the cable

and twist it so that no individual copper-strands stick out (caution:

danger of short-circuit). Loosen the binding post and insert the cable

from below. Tighten the binding post rmly!

Speaker Cables

Thin speaker cables are not a good way to transport the electrical

signal between amplier and speaker.

As such, the supplied speaker cables are to be considered an interim

solution, in case you didn’t order speaker cables with your speakers

and do not have quality cables available.

For the RS-54, we recommend using our nuCable LS 2,5 Studioline

2 x 2,5 mm2 speaker cable for cable lenghts under 10 m. For longer

cable runs, we recommend the 2 x 4 mm2 nuCable LS 4 Studioline.

Mode Switch

Between the binding posts, you will nd a two-position switch. With

this switch, you optimize the sound of the speaker to either the

direct-radiating compact speaker- or the Dolby Atmos Enabled up-

ring role.

With the switch In the position, the RS-54 is a Direkt (direct)

normal, direct-radiating compact 2-way loudspeaker. Use this

setting if you want to use the RS-54 as your main- or surround-

loudspeakers. (more on page 4 and 5)

Setting the switch to is recommended Reektierend (reecting)

when using the speaker as a ceiling-reecting speaker for immersi-

ve audio formats. This setting changes the frequency response and

dispersion characteristics of the speaker to fulll all Dolby Labo-

ratories requirements for Dolby Atmos enabled up-ring speakers

with Dolby Speaker Technology. The RS-54 is fully tested and cer-

tied by Dolby Laboratories

Direkt (direct)

Reektierend (reecting)

Direct / Reecting mode-switch

EN 09/2020 · nuLine RS-54

Tuotetiedot

Merkki:	Nubert
Kategoria:	Kaiutin
Malli:	nuLine RS-54

Tarvitsetko apua?

Jos tarvitset apua merkille Nubert nuLine RS-54 esitä kysymys alla ja muut käyttäjät vastaavat sinulle

Nimesi*

Sähköpostisi*

Kirjoita kysymyksesi tähän

Kaiutin Nubert Käyttöohjeet

Nubert nuZeo 15 Käyttöohje

11 Helmikuuta 2025

Nubert nuBoxx A-125 pro Käyttöohje

11 Helmikuuta 2025

Nubert nuLine RS-54 Käyttöohje

1 Helmikuuta 2025

Kaiutin Käyttöohjeet

Viimeisimmät Kaiutin Käyttöohjeet

LD Systems STINGER G3 TMB Käyttöohje

8 Huhtikuuta 2025

JBL Conceal C83 Käyttöohje

8 Huhtikuuta 2025

JBL Control 426LP Käyttöohje

8 Huhtikuuta 2025

Crestron SAROS ICE4T Käyttöohje

7 Huhtikuuta 2025

Crestron SAROS ICI6T Käyttöohje

7 Huhtikuuta 2025

Crestron SAROS IC8T Käyttöohje

7 Huhtikuuta 2025

Focal K2 Power M FRAK Käyttöohje

5 Huhtikuuta 2025

Turbosound PQ12-SB Käyttöohje

3 Huhtikuuta 2025

Trust Tytan GXT 658 Käyttöohje

3 Huhtikuuta 2025

Turbosound PQ15-YB Käyttöohje

3 Huhtikuuta 2025