Neumann LH 48 Käyttöohje
Neumann
kaiuttimen tuki
LH 48
Lue alta 📖 käyttöohje suomeksi merkille Neumann LH 48 (2 sivua) kategoriassa kaiuttimen tuki. Tämä opas oli hyödyllinen 31 henkilölle ja sai 4.3 tähden keskimäärin 16 käyttäjältä
Sivu 1/2
Important safety and mounting instructions
• Have the product mounted by a specialist.
• Due to his/her technical training, know-how and experience as well
as knowledge of relevant provisions, regulations and standards, the
specialist must be able to assess assigned tasks, recognize poten-
tial hazards and ensure appropriate safety measures. The following
safety and mounting instructions are addressed to this specialist.
•
Read and follow the safety and mounting instructions, keep these
instructions and always include them when passing the LH48 on
to third parties.
•
Also read and follow the installation instructions contained in the
operating manual of the mounted loudspeaker.
• When mounting, observe and follow the local, national and interna-
tional regulations and standards.
•
Do not install the LH48 in locations where it is exposed to externally
generated vibrations.
• Always use the original Neumann supplied parts.
•
Mount the LH48 in combination with other accessories from the
Neumann mounting hardware range to loudspeakers with a maxi-
mum weight of 65 kg (143.3 lbs).
Download the PDF file “Hardware Mounting Matrix” from
www.neumann.com. Only combine the Neumann mounting
hardware as specified in the “Hardware Mounting Matrix”.
CAUTION!
Danger of injury and material damage
due to dropping of the loudspeaker/mounting hardware!
Unless the LH48 is properly fastened, the loudspeaker together
with the mounting hardware can drop down.
X
Have the loudspeaker held by a second specialist who is physi-
cally able to do so. The requirements mentioned earlier also
apply to this specialist.
X
When mounting the loudspeaker, provide a sufficien additional
protection against dropping.
If you use other M8 bolts than the supplied ones to fasten the LH48
to other Neumann mounting hardware and/or K&M monitor stands,
the loudspeaker together with the mounting hardware can drop
down.
X
Always use the supplied bolts to fasten the LH 48.
• Fasten the LH 48 to the K&M monitor stand. Use the two bolts C and
fasten them with a torque of 10 Nm (see fi . 1) .
•
Attach the mounting hardware to the LH 48 (see the “Hardware
Mounting Matrix”). Use the two bolts D and fasten them with a
torque of 20 Nm (see fi . 2). Also read and follow the safety and
mounting instructions contained in the operating manual of the
selected mounting hardware.
•
If different mounting positions are possible, choose mounting points
that minimize leverage when the loudspeaker is tilted. As a rule,
this means that the other Neumann mounting hardware is centrally
mounted to the LH48.
•
Attach your loudspeaker to the Neumann mounting hardware. Follow
the safety and mounting instructions of the loudspeaker and the
mounting hardware.
•
Use safety wires to additionally protect the loudspeaker and the
mounting hardware against tipping/dropping. The safety wires, rope
terminations and coupling links must comply in their dimensioning
and condition with the regulations and standards of the country in
which they are used and must reliably prevent tipping/droppin of
a loudspeaker and the attached mounting hardware.
• Make sure that ...
–
the LH48, the K&M monitor stand, the associated mounting hard-
ware and the loudspeaker cannot tip over or drop down, even if
the power or audio cables are pulled;
–
you replace the safety wires and coupling links by new ones when
they have prevented tipping/dropping;
–
you check every 3 months if all screws are properly tightened
and if the LH48, the K&M monitor stand and associated mount-
ing hardware, additional fastening elements, safety wires and
coupling links, as well as the loudspeaker are in proper condition.
In case of any damage or any deviation from the safety and mounting
instructions, immediately dismount the loudspeaker, the LH48 and
the additional mounting hardware used.
Delivery includes
A: 1 x LH48 stand adaptor plate
B: 2 x M6x16 bolts with countersunk Allen key head
C: 2 x M8x20 bolts with countersunk Allen key head
D: 2 x metal washers
E: 2 x M8 nuts
F: 2 x cover caps, PVC
G: 1 x 4 mm Allen key
H: 1 x 5 mm Allen key
Specification
Weight 0.260 kg (0.6 lbs)
Dimensions 4 x 60 x 146 mm (H x W x D)
5
/
32
" x 2
3
/
8
" x 5
3
/
4
" (H x W x D)
Max. load 65.0 kg (143.3 lbs)
Guarantee
For the current terms and conditions of the product guarantee please
visit www.neumann.com.
EN
GEORG NEUMANN GMBH · LEIPZIGER STR. 112 · 10117 BERLIN · GERMANY 10/15 · 549114/A02
TEL +49 (0)30 / 41 77 24-0 · FAX -50 · HEADOFFICE@NEUMANN.COM · WWW.NEUMANN.COM
LH 48
M
ounting manual
Mounting flange adaptor
Tuotetiedot
| Merkki: | Neumann |
| Kategoria: | kaiuttimen tuki |
| Malli: | LH 48 |
Tarvitsetko apua?
Jos tarvitset apua merkille Neumann LH 48 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
kaiuttimen tuki Neumann Käyttöohjeet
24 Tammikuuta 2025
24 Tammikuuta 2025
24 Tammikuuta 2025
23 Tammikuuta 2025
23 Tammikuuta 2025
23 Tammikuuta 2025
kaiuttimen tuki Käyttöohjeet
- kaiuttimen tuki Blaupunkt
- kaiuttimen tuki Ultimate
- kaiuttimen tuki Vonyx
- kaiuttimen tuki Konig & Meyer
- kaiuttimen tuki Sonorous
- kaiuttimen tuki Bluesound
- kaiuttimen tuki Nubert
- kaiuttimen tuki Velleman
- kaiuttimen tuki Xtech
- kaiuttimen tuki Multibrackets
- kaiuttimen tuki Valcom
- kaiuttimen tuki SoundTube
- kaiuttimen tuki Electro-Voice
- kaiuttimen tuki Teufel
- kaiuttimen tuki Omnitronic
Viimeisimmät kaiuttimen tuki Käyttöohjeet
27 Helmikuuta 2025
20 Helmikuuta 2025
20 Helmikuuta 2025
6 Helmikuuta 2025
5 Helmikuuta 2025
24 Tammikuuta 2025
15 Tammikuuta 2025
14 Tammikuuta 2025
13 Tammikuuta 2025
12 Tammikuuta 2025