I-PRO WV-X6533LNS Käyttöohje

I-PRO Valvontakamera WV-X6533LNS

Lue alta 📖 käyttöohje suomeksi merkille I-PRO WV-X6533LNS (4 sivua) kategoriassa Valvontakamera. Tämä opas oli hyödyllinen 44 henkilölle ja sai 5.0 tähden keskimäärin 22.5 käyttäjältä

Lataa PDF

Sivu 1/4

WV-Q122AS

WV-Q121BS

A B

Step3

Fixing the camera

Step2

Making connections

WV-X6533LNS

Preparations

Other items that are needed (not included)

Prepare the required parts for each installation method before starting the installation. The following

are the requirements for the various installation methods.

Prepare the foundation of the installation site, installation support, and any other installation setting

with heavy salt damage resistance treatment.

Installation method

Mounting

screw

Minimum pull-out

strength/ 1pcs.

AWhen hanging the camera from ceiling

Use the ceiling mount bracket (WV-Q121BS

M10 screws/

4pcs.

1411 N {317 lbf}

BWhen installing the camera on a wall

Use the wall mount bracket (WV-Q122AS

M10 screws/

4pcs.

823 N {185 lbf}

Preparations before installation

【

】

Insert an SD memory card as occasion demands.

For the detailed procedures of inserting and removing an

SD memory card, refer to Important Information on the

provided CD-ROM.

① Loosen 2 SD slot cover fixing screws (M4) using a

Phillips screwdriver, and open the SD slot cover.

② Insert an SD memory card in the SD slot. Push in

straight until the end and confirm that a clicking sound

is heard. Take your ngers off the SD memory card

and check that its back end does not protrude over

the SD guide rib.

③ Attach the SD slot cover again.

Recommended tightening torque of the SD slot cover

xing screws: 1.38 N·m {1.02 lbf·ft}

*1 For details on procedure for attaching mount bracket and

camera, read the operating instructions of each mount bracket.

Installation

The installation tasks are explained using 4 steps.

⇨

Step1

Fix the mount bracket

and hang the camera

Step4

Configure the network

settings

• Remove the camera using the reverse order of the installation procedures.

Cable cover 1 pc. ........................................................

Waterproof tape 1 pc. ..................................................

RJ45 waterproof connector cover 1 pc. ......................

RJ45 waterproof connector cap 1 pc. .........................

Rain wash coating label 1 pc. ......................................

8P alarm cable 1 pc. ...................................................

24 V AC power supply connector kit 1 set ....................

(Power supply connector housing: 1 pc., Contact: 3 pcs.)

Special hexagon screw

.................................. 5 pcs.

(of them, 1 for spare)

Locking washers 5 pcs. ...............................................

(of them, 1 for spare)

About the user manuals

Standard accessories

Installation Guide (this document) 1 pc. .......................

IMPORTANT SAFETY INSTRUCTIONS 1 pc. ...............

CD-ROM*

.......................................................... 1 pc.

Code label*

........................................................ 1 pc.

The CD-ROM contains the several kind of operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. Use caution not to lose this label.

Waterproof tape

*3 The screws are necessary when installing the camera on a separately sold mount bracket.

The following parts are used during installation procedures.

Network Camera

Model No. WV-X6533LNS, WV-S6532LNS

Installation Guide

CAN ICES-3(A)/NMB-3(A)

For Canada

WARNING:

• To prevent injury, this apparatus must be securely

attached to the wall/ceiling in accordance with the

installation instructions.

• All work related to the installation of this product

should be made by qualified service personnel or

system installers.

• The installation shall be carried out in accordance

with all applicable installation rules.

• The connections should comply with local electri-

cal code.

• Batteries (battery pack or batteries installed) shall

not be exposed to excessive heat such as sun-

light, fire or the like.

• This equipment is compliant with Class A of

CISPR 32. In a residential environment this equip-

ment may cause radio interference.

• Operation of this equipment in a residential envi-

ronment could cause radio interference.

CAUTION:

• The network camera is only intended for a con-

nection to an ethernet or PoE+ network without

routing to the outside plant.

• RISK GROUP 2 IR emitted from this product.

Avoid eye exposure. Use appropriate shielding or

eye protection.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household

waste.

For proper treatment, recovery and recycling of old products and used batteries, please take

them to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with

the requirement set by the Directive for the chemical involved.

: Caution, infrared radiation

: Direct current symbol

: Alternating current symbol

• Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

• For information about the basic description of this product, refer to the Important Information on

the provided CD-ROM. For information about how to perform the settings and how to operate the

camera, refer to the Operating Instructions on the following our support website.

https://i-pro.com/global/en/surveillance/documentation_database

• Before reading this manual, be sure to read the Important Information.

The model number and serial number of this prod-

uct may be found on the surface of the unit.

You should note the model number and serial

number of this unit in the space provided and

retain this book as a permanent record of your

purchase to aid identification in the event of theft.

Model No.

Serial No.

For U.S.A.

NOTE: This equipment has been tested and found

to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equip-

ment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case

the user will be required to correct the interference

at his own expense.

FCC CAUTION: Changes or modifications not

expressly approved by the party responsible for

compliance could void the user's authority to oper-

ate the equipment.

For U.S.A.

Supplier’s Declaration of conformity

Trade name : i-PRO

Model No. : WV-X6533LNS, WV-S6532LNS

Responsible Party :

i-PRO Americas Inc.

8550 Fallbrook Drive, Suite 200 Houston,

Texas 77064

Support Contact : 1-800-513-5417

This device complies with part 15 of FCC Rules.

Operation is subject to the following two conditions :

(1)This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

For U.S.A.

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

6) Only use attachments/accessories specified by the manufacturer.

7) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

8) Unplug this apparatus during lightning storms or when unused for long periods of time.

9) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Troubleshooting

Before requesting service, refer to “Troubleshooting” of Important Information in the CD-ROM

and Operating Instructions on our support website. Then, confirm the trouble.

Included Installation Instructions

Open Source Software

⿟This product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

⿟Customers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

⿟Refer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

⿟Please note that we shall not respond to any inquiries regarding the contents of the source code.

Product documentation is composed of the following documents.

⿟Installation Guide (this document): Explains installation, mounting, cable connections, and

network connections. This manual uses the WV-X6533LNS as an example in the explanations.

⿟Important Information (included in the CD-ROM):

Provides basic information about the prod-

uct such as Precautions for installation, Parts and functions, etc..

⿟Operating Instructions (on our support website): Explains how to perform the settings and

how to operate this camera.

"<Control No.: C****>" used in this document should be used to search for information on our support website

(https://i-pro.com/global/en/surveillance/training_support/support/technical_information) and will guide you to

the right information.

Note:

• The external appearance and other parts shown in this manual may differ from the actual

product within the scope that will not interfere with normal use due to improvement of the

product.

• SDXC/SDHC/SD memory card is described as SD memory card.

IMPORTANT:

• Refer to our support website

(

https://i-pro.com/global/en/surveillance/training_support/support/

technical_information <Control No.: C0120>

) for information on

the minimum pull-out strength.

• Prepare four mounting screws (M10) to be mounted on ceiling or

wall separately.

• Select screws according to the material of the location that the

camera will be mounted to. In this case, wood screws and nails

should not be used.

• Please consider using anti-corrosive mounting screws or caulking.

• If the mounting location such as plaster board is too weak to

support the total weight, the area shall be sufficiently reinforced.

SD slot

SD memory card

(with label facing down)

SD slot cover

【

】

Prepare the cables from camera side.

◆

When the only necessary connection to

camera is an Ethernet cable

Do not remove the cable case (2 positions),

use it as it is.

◆

When using 24 V AC, EXT I/O device, or

audio I/O device

Using a Phillips screwdriver detach each cable

case fixed to the top of the camera by 4

screws (M4), and pull out the cable stored

inside. Discard the cable case.

RJ45

Network

cable

Alarm input/output·

Audio input/output

cable

Power supply

terminal

(24 V AC)

Power cable case

Multi cable case

Indication

label

SD slot cover fixing screws

SD guide rib

Ns1120-1042

Printed in China

(Heavy salt damage resistance)

For professional use only

Fixing screws (4 pcs.) (M10: locally procured)

180~190 mm

{7-3/32 inches~

7-15/32 inches}

Step1 Fix the mount bracket and hang the camera

Here explains an example of installation on a wall

using wall mount bracket (

WV-Q122AS

). For detailed

installation information and procedure, refer to

operating instructions of each mount bracket.

【

】

Process the installation surface.

Decide the attachment position and bore holes for

screws or anchors on the wall and a hole for wiring

as occasion demands.

【

】

Pass a cable into mount bracket and fix it

on the installation surface.

①

Insert the cables coming from installation surface from rear

surface of mount bracket to internal and pull them out from

camera attachment port (cable cover attachment side).

When passing the cables into mount bracket, take

care not to apply unreasonable force to the cables.

②

Apply waterproof treatment to the drilled installation

surface and the cap of the mount bracket back-

side.

③ Attach the mount bracket to wall surface using

fixing screws (4 pcs.) (M10: locally procured).

【

】

Attach the cable cover (accessory) to the

mount bracket.

① Fix the cable cover to the mounting bracket using

special hexagonal screws and locking washers by

tightening the screws using a hexagonal wrench

for M5 screw (locally procured).

Adjust the direction of the cable cover so that the

“REAR” mark of the cable cover points towards

the mount bracket.

Recommended tightening torque:

9.8 N·m{7.23lbf·ft}

IMPORTANT:

• Camera mounting screw (hexagon screw (M6))

included with

WV-Q121BS / WV-Q122AS

cannot

be used. Use the special hexagon screw that has

a large washer included with the camera.

② Remove the tape as the installed auxiliary wire is

temporarily fixed to the inside of the cable cover

with tape.

IMPORTANT:

• After waterproofing the hole for fixing mount bracket, the port for pulling out the cable on

installation surface, and the cap part on rear surface of mount bracket, fix the mount

bracket on the installation surface.

• Fixing screw: Minimum pull-out strength (per 1 pc.)

WV-Q121BS 1411 N {317 lbf}

WV-Q122AS 823 N {185 lbf}

• Adjust the length of cable from camera attachment port of mount bracket to cable end to

180~190 mm {7-3/32 inches~7-15/32 inches}. (If the cable that is pulled out is too long,

storage after wiring becomes difficult. On the contrary, if it is too short, the cable cannot

reach to the camera when installing the camera. Adjust the cable length carefully.)

IMPORTANT:

• The maximum length of the Ethernet cable (locally procured) is 100 m {Approx. 328 ft}, and

the external dimensions of it are from ø5 mm {ø3/16 inches} to ø6.5 mm {ø1/4 inches}.

【

】

Process the Ethernet cable (locally procured) and attach

the waterproof connector cover and cap (accessory).

First pass the Ethernet cable through the RJ45

waterproof connector cap (accessory) and then

through the RJ45 waterproof connector cover

(accessory). Next, use a specialized tool (locally

procured) to crimp the RJ45 plug (locally procured) to

the end of the Ethernet cable.

RJ45

waterproof

connector

cover

(accessory)

RJ45

waterproof

connector cap

(accessory)

RJ45 plug

(locally

procured)

Ethernet cable (locally procured)

Note:

• The horizontal and vertical rotating parts of the

camera are fixed by tape. Do not remove the

tape until fixing of the camera is completed.

• The camera is not fixed. Take care not to hit

the camera against periphery.

• Retain a work space of 800 mm

{31-1/2 inches}

or more from the cable cover to the ground

surface when you hang the camera from it.

• The installed auxiliary wire and the safety wire

are designed assuming the only camera is

suspended. Do not hang any object other than

the camera.

Mount bracket (example:

WV-Q122AS

)

180~190 mm

{7-3/32 inches~

7-15/32 inches}

Camera

attachment port

Cap

Cable cover

(accessory)

Installed

auxiliary wire

Mount bracket

(example:

WV-Q122AS

)

Front of the bracket

Special hexagon screws

(With locking washers)

Wire stopper

Wire hook

section

Mount bracket

(example:

WV-Q122AS

)

Cable

cover

Wire hook on the upper part of camera

Camera

body

②Safety wire

①Installed

auxiliary wire

REAR mark

【

】

Hang the camera from the installed auxiliary

wire of the cable cover, and attach the safety

wire to the mounting bracket.

① Move the camera to the installation location and

hitch the installed auxiliary wire of the cable cover

to the wire hook on the upper part of camera.

Next, lower the wire stopper to prevent the

installed auxiliary wire from coming off.

② Attach the safety wire of the camera to the wire

hook section of mount bracket.

For the safety wire attachment position, refer to

operating instructions of each mount bracket.

• Take care not to remove the rubber parts from inside the RJ45 waterproof connector cover (accessory).

For U.S. and Canada:

i-PRO Americas Inc.

https://www.i-pro.com/

For Europe and other countries:

i-PRO Co., Ltd. Fukuoka, Japan

https://www.i-pro.com/

i-PRO EMEA B.V. UK Branch

1010 Cambourne Business Park,

Cambridgeshire CB23 6DP

Authorised Representative in EU:

i-PRO EMEA B.V.

Laarderhoogtweg 25, 1101 EB

Amsterdam, Netherlands

Tuotetiedot

Merkki:	I-PRO
Kategoria:	Valvontakamera
Malli:	WV-X6533LNS

Tarvitsetko apua?

Jos tarvitset apua merkille I-PRO WV-X6533LNS esitä kysymys alla ja muut käyttäjät vastaavat sinulle

Nimesi*

Sähköpostisi*

Kirjoita kysymyksesi tähän

Valvontakamera I-PRO Käyttöohjeet

I-PRO WV-S15600-V2L Käyttöohje

1 Tammikuuta 2025

I-PRO WV-X15500-V3L Käyttöohje

17 Joulukuuta 2024

I-PRO WV-X15700-V2LN Käyttöohje

17 Joulukuuta 2024

I-PRO WV-X22500-V3L Käyttöohje

17 Joulukuuta 2024

I-PRO WV-S2536LA Käyttöohje

17 Joulukuuta 2024

I-PRO WV-S2536LTA Käyttöohje

17 Joulukuuta 2024

I-PRO WV-S25500-F3L Käyttöohje

17 Joulukuuta 2024

I-PRO WV-S25500-F6L Käyttöohje

17 Joulukuuta 2024

I-PRO WV-S25600-V2L Käyttöohje

17 Joulukuuta 2024

I-PRO WV-S25500-V3L Käyttöohje

17 Joulukuuta 2024

Valvontakamera Käyttöohjeet

Viimeisimmät Valvontakamera Käyttöohjeet

Technaxx TX-192 Käyttöohje

28 Tammikuuta 2025

Milesight MS-C3363-FPNA Käyttöohje

25 Tammikuuta 2025

DSC HS2TCHP Käyttöohje

25 Tammikuuta 2025

Milesight MS-C4461-EB Käyttöohje

25 Tammikuuta 2025

GVI Security videoPLUS AOD-112N Käyttöohje

25 Tammikuuta 2025

Sony SNC-ER585H Käyttöohje

25 Tammikuuta 2025

Sony SNC-ZM551 Käyttöohje

25 Tammikuuta 2025

Sony SNC-ZR550 Käyttöohje

25 Tammikuuta 2025

Milesight MS-C2973-PB Käyttöohje

25 Tammikuuta 2025

Milesight MS-C5363-PB Käyttöohje

25 Tammikuuta 2025