GVI Security autoIP GV-NC-201VA Käyttöohje

GVI Security Valvontakamera autoIP GV-NC-201VA

Lue alta 📖 käyttöohje suomeksi merkille GVI Security autoIP GV-NC-201VA (4 sivua) kategoriassa Valvontakamera. Tämä opas oli hyödyllinen 18 henkilölle ja sai 4.8 tähden keskimäärin 9.5 käyttäjältä

Sivu 1/4
WWW.GVISS.COM
GV-NC-201VA
1.3 Megapixel, Auto Focus Dome Camera
QUICK START GUIDE
GVI Security • Toll Free: 888-595-2288 • Fax: 972-245-7333
This product specications and manual are also available in pdf format at www.gviss.com
The information is subject to change without notice • v2.23.10
2
1. Review Package Contents
2. Make Connections to Camera
Connector Pin No. Definition Remarks
Reset Button - Restore to factory defualt
BNC - Analog Video Output
Alarm I/O
1 Output+
Alarm Connection
2 Output-
3 Input+
4 Input-
Audio I/O
1 Input
Two-way audio transmission
2 GND
3 Output (R)
4 Out (L)
Power
DC
12V
1 Power
Power Connection
2 Reserved
3 GND
AC
24V
1 Power-1
2 Earth GND
3 Power-2
RJ45 - 10/100 Ehternet / PoE
Dome Camera Power Cable Self Tapping Screws (x4) Plastic Screw Anchors (x4)
Security Torx Rubber Washers (x6)
CD (bundled software and
documentation
Quickstart Guide
GVI Security • Toll Free: 888-595-2288 • Fax: 972-245-7333
This product specications and manual are also available in pdf format at www.gviss.com
The information is subject to change without notice • v2.23.10
3
•Connectthecameratothenetworkusingashielded
networkcable(CAT5e/CAT6)
 •Optionally–connectexternalinput/outputdevices,e.g.
alarm devices
 •Optionally–connectanactivespeakerand/orexternal
microphone
•PowerthecameraeitherthroughPOE(PowerOver
Ethernet),12VDCor24VACpowersources,thePOE
connectionwouldbeautodetectedbythecamera.
3. Assign an IP Address
MostnetworkstodayhaveaDHCPserverthatautomaticallyassignsIPaddressesto
connecteddevices.IfyournetworkdoesnothaveaDHCPservertheautoIPcamerawill
use192.168.0.250asthedefaultIPaddress.
TheautoIPDiscoveryToolcanbeusedtoassignanewIPaddress.Thetoolisavailable
ontheCDsuppliedwiththisproductoritcanbedownloadedfromhttp://www.gviss.
com/support/ip_support.php.
Note:ThecomputerrunningtheautoIPDiscoveryToolmustbeonthe
samenetworksegment(physicalsubnet)astheautoIPcameras.
 •VerifythattheautoIPcamerasareconnectedtothe
network,andthatthepowerhasbeenapplied.
 •OpentheautoIPDiscoveryTool
 •Click“DeviceSearch”tolistalloftheautoIPcamerason
thenetwork.
 •RightclickonthedesiredautoIPcameraandselect
“NetworkSetup”toadjustthenetworksettings.

Tuotetiedot

Merkki: GVI Security
Kategoria: Valvontakamera
Malli: autoIP GV-NC-201VA

Tarvitsetko apua?

Jos tarvitset apua merkille GVI Security autoIP GV-NC-201VA esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Valvontakamera GVI Security Käyttöohjeet

Valvontakamera Käyttöohjeet

Viimeisimmät Valvontakamera Käyttöohjeet

Technaxx

Technaxx TX-192 Käyttöohje

28 Tammikuuta 2025
DSC

DSC HS2TCHP Käyttöohje

25 Tammikuuta 2025
Sony

Sony SNC-ER585H Käyttöohje

25 Tammikuuta 2025
Sony

Sony SNC-ZM551 Käyttöohje

25 Tammikuuta 2025
Sony

Sony SNC-ZR550 Käyttöohje

25 Tammikuuta 2025
Sony

Sony SNC-VM632R Käyttöohje

25 Tammikuuta 2025