Graco InvisiPac HM50 24Y114 Käyttöohje
Graco
Ei luokiteltu
InvisiPac HM50 24Y114
Lue alta 📖 käyttöohje suomeksi merkille Graco InvisiPac HM50 24Y114 (4 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 10 henkilölle ja sai 4.9 tähden keskimäärin 5.5 käyttäjältä
Sivu 1/4

Read instruction manual 334784 for complete
instructions and warnings. This Quick Guide is not
a substitute for reading and understanding all
instructions manuals and warnings labels
supplied with the equipment.
Turn System
On
Screen Navigation
Turn System
Off
Integrated Systems
Stand-Alone Systems
Select
Program
1. Arrow left _to
navigate to the “PC
Control” screen.
2. Enter the screen
and arrow up or
down _. Press
to select a pro-
gram.
Clear
Errors
Acknowledge errors by
pressing _ once for
each error.
Display will show “No
Active Errors” unless
error was unable to
clear. Seek technical
support if any error
persists.
- or -
EN
335007B
Quick Guide
InvisiPac
®
Pattern Controller
1
335007

Wiring Installation
Integrated InvisiPac Systems
• Use melter System Enable
instead of this one
• Use this Disable to hold
guns from dispensing with-
out shutting off the heat.
Power
RED
BLACK
GRN/YL
PLC Inputs
0-30 VDC
Bi-polar
Isolated
Alarm Outputs
0-30 VDC or 0-240 VAC
Dry contact output
No alarm: closed
Alarm: open
Valves (Guns)
24 VDC
1A max each
Triggers
24 VDC
NPN, PNP, Dry Contact
Encoders
15 VDC
Line driver (RS422)
Differential A/B signals
(Z is not used)
NOTE: Swap A with B to
reverse direction
Run Ups
24 VDC
I/P or V/P
Enable
Rising edge enables
Falling edge disables
Disable
Pull high to disable
Program Select
4 bits, 15 programs
(0000 is unused)
EXAMPLE:
1010 into 3,2,1,0
Selects program 10
LINE 1 ALARM
LINE 2 ALARM
CAN
COMMUNICATION
BROWN
BLACK
BLUE
WHITE
BROWN
BLACK
BLUE
WHITE
RED
BROWN
WHITE
YELLOW
GREEN
BLUE
BARE
BARE
BLUE
GREEN
YELLOW
WHITE
BROWN
RED
BROWN
BLK or WH
BLUE
BLUE
BLK or WH
BROWN
Dial Settings
0 - Integrated
1 - Stand-alone
Mini DIN
BLUE
BROWN
DIN “I”
BLACK
BLACK
2
335007

Line
Mode
2.
No Encoder
• Check time based or dis-
tance mode.
• Un-check encoder box
(PC-8e only) ._.
• Set fixed speed to
adjust last measured
product length_.
Encoder (PC-8e only)
• Un-check time based
mode.
• Check encoder box_.
• Set pulses per mm_to
adjust last measured
product length .
• Set low line speed advi-
sory level_.
Trigger
Setup
3.
• Set trigger polarity _. Indicators show on _or off _.
• Assign to line 1 or 2 (PC-8e only) .
General 4.
No Run Up
• Disable pressure com-
pensation.
• Enable or disable modu-
lated bead (PC-8e only).
Run Up (PC-8e only)
• Enable pressure
compensation.
Gun (Valve)
Setup
5.
Set gun open_ _and- ---close compensation
• ~5ms for high speed guns
• ~10ms for standard guns
NOTE: Applies to high speed lines requiring precise beads.
Run Up
Control
6.
Set Modulated Bead Curve
• Set output value at
line speed_ .
• Set max and min .
Set Run Up Curve
• Set output value _at
line speed_ .
• Set max and min .
PC Setup Screens
1. Event Map 2. Line Mode
3. Trigger Setup 4. General
5. Gun (Valve) Setup 6. Run Up Control
3335007
Tuotetiedot
Merkki: | Graco |
Kategoria: | Ei luokiteltu |
Malli: | InvisiPac HM50 24Y114 |
Tarvitsetko apua?
Jos tarvitset apua merkille Graco InvisiPac HM50 24Y114 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Ei luokiteltu Graco Käyttöohjeet
31 Tammikuuta 2025
14 Tammikuuta 2025
8 Tammikuuta 2025
25 Joulukuuta 2024
25 Joulukuuta 2024
22 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
Ei luokiteltu Käyttöohjeet
- Ei luokiteltu Accsoon
- Ei luokiteltu Tripp Lite
- Ei luokiteltu Jane
- Ei luokiteltu Grunkel
- Ei luokiteltu Britax
- Ei luokiteltu Vocopro
- Ei luokiteltu Digitech
- Ei luokiteltu Europalms
- Ei luokiteltu Memphis Audio
- Ei luokiteltu Wimberley
- Ei luokiteltu Peerless-AV
- Ei luokiteltu AVM
- Ei luokiteltu Kendall Howard
- Ei luokiteltu Hypnos
- Ei luokiteltu Grasslin
Viimeisimmät Ei luokiteltu Käyttöohjeet
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025