Deaf Bonce Machete MA-130.4 Käyttöohje
Deaf Bonce
Vastaanotin
Machete MA-130.4
Lue alta 📖 käyttöohje suomeksi merkille Deaf Bonce Machete MA-130.4 (20 sivua) kategoriassa Vastaanotin. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/20
AMPLIFIER CLASS AB
M54 M84 MA-130.4
http://deafbonce.com
FOUR-CHANNEL AMPLIFIER
1. Introduction.
2. Safety instructions.
3. Typical installation sequence.
4. Connection methods.
5. Wiring diagrams.
6. Selection of the diameter of power cables and speaker cables.
7. Specifications.
8. Possible faults and their solutions.
9. Box content.
10. Warranty and maintenance info.
11. Information on disposal of the electrical and electronic equipment (for the
European countries with separate waste collection).
2
C O N T E N T S EN
1 . I N T R O D U C T I O N EN
1. This unit is for vehicles with a 12V battery and negative grounding. Before installing in recreational vehicles, trucks or buses,
check the battery voltage.
2. Check the state of on-board power supply of your vehicle, the battery and the generator. When the motor is running,
depending on the ambient temperature, the voltage to be outputted by the generator is within the range of 14 to 14.7 V. Open
circuit voltage (OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the generator and
the battery capacity is enough to provide increased consumption.
For example, for the power of the amplifier 1000 W, the rated current of the generator is required at the rate of 1000 W / 13 V
= 77 amperes. A more powerful amplifier requires a more powerful generator as well as an additional battery.
3. Do not place the amplifier in either the engine compartment or the places exposed to water, moisture, dust or dirt.
4. Never stretch the cables outside the car and near the moving parts of the car. This can lead to destruction of the insulating
layer, short circuit and fire.
5. The amplifier should be installed in areas of the car where the temperature is from 0 °C (32 °F) to 55 °C (131 °F). The amplifier
should be in a place with a good air circulation. The horizontal position of the amplifier is the best way to install.
6. During the operation the amplifier may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated
that may be dangerous.
7. To improve the cooling of the amplifier, it is recommended to clean periodically the heatsink from dust. When cleaning the
heatsink strong solvents should not be used as they may damage the amplifier. Do not use compressed air, because solids can
penetrate inside the amplifier. Cleanings best done with wet towels or cloth.
8. Make sure that the location of the amplifier does not violate the proper operation of mechanical and electrical devices of
the vehicle.
9. Make sure that during the installation and connection of the battery, the power cables are not shorted.
10. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe
or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies
close to the parts exposed to heat.
12. Make sure that all the cables are fixed over the entire length. Also make sure that their outer protective shell is non-
combustible. Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the amplifier.
13. Select a diameter of the power cable in accordance with the power of the amplifier and the recommendations provided
here. Power cables are extremely important since they directly affect the system damping factor and sound quality. The cables to
the battery must be in the copper crimp terminals with the help of a hydraulic press, and is well secured to the battery terminals.
14. To avoid accidental damage, keep the amplifier in its original packaging prior to installation.
15. Use high-quality copper speaker cables.
CAUTION!!! High sound pressure can damage your health! Please use the common sense when controlling volume!
2 . S A F E T Y I N S T R U C T I O N S
1. Before installing the amplifier disconnect the battery from the electrical system.
2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation
of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: Power cable)
3. Connect the power supply in accordance with polarity. Connect the (+) terminal to the cable coming from the battery and
the (-) terminal to the vehicle chassis. Caution! Using an amplifier of more than 1000 Watts it is necessary to put + and – directly
from battery terminals.
4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of
the power cable to the holder after connecting the other end to the amplifier. Do not install the fuse.
5. For proper grounding of the device (-), use a screw in the car body; clean the oil, paint from metal if needed, checking with
the tester the continuity between the negative terminal of the battery (-) and the anchoring point. If possible, connect all
components to the same grounding point; this solution allows to eliminate much of the noise generated during sound
reproduction.
6. Route all signal cables next to each other and separately from the power cables.
7. Connect the wires of RCA input. The input signal must be between 0.3 VRMS and 5 VRMS.
8. Connect the output of the amplifier via speaker cable with a maximum diameter of 8 AWG (8.4 mm2).
9. To activate the amplifier, it is necessary to apply the positive potential of 12 volts to the control input of the amplifier
(REMOTE IN) through a switch or a corresponding control output (REMOTE OUT) with the head unit (HU).
10. LED indicator on the front panel lights up in green, indicating that the device is turned on. LED indicator lights up in red
when the outputs are overloaded, if the temperature protection is activated, if there is a short circuit in the system cables to the
heatsink and if the amplifier is faulty.
11. The fuses are located next to the connectors of power supply and output. To replace the fuses remove them from the
heatsink. It is obligatory to install a fuse of the same value (only at MA-130.4).
12. Fasten the amplifier properly when installing it in the vehicle. If the component is disconnected during driving, it may
cause serious damage to the passengers of the car or another vehicle.
13. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.
Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the light
bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive terminal of
the battery.
3 . T Y P I C A L I N S TA L L AT I O N S EQ U E N C E
3
Thank you for purchasing this Deaf Bonce product! Deaf Bonce is committed to the creation of extremely high-profile
systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you
read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.
Tuotetiedot
| Merkki: | Deaf Bonce |
| Kategoria: | Vastaanotin |
| Malli: | Machete MA-130.4 |
Tarvitsetko apua?
Jos tarvitset apua merkille Deaf Bonce Machete MA-130.4 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Vastaanotin Deaf Bonce Käyttöohjeet
17 Helmikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
22 Tammikuuta 2025
Vastaanotin Käyttöohjeet
- Vastaanotin Bosch
- Vastaanotin Power Dynamics
- Vastaanotin Vonyx
- Vastaanotin Akg
- Vastaanotin Jensen
- Vastaanotin Hartke
- Vastaanotin Philips
- Vastaanotin Goobay
- Vastaanotin Avantree
- Vastaanotin Godox
- Vastaanotin Cayin
- Vastaanotin Meridian
- Vastaanotin Fender
- Vastaanotin Axton
- Vastaanotin Kogan
- Vastaanotin DJI
- Vastaanotin Sony
- Vastaanotin Pro-Ject
- Vastaanotin Yamaha
- Vastaanotin Morel
- Vastaanotin Extron
- Vastaanotin Lindy
- Vastaanotin NuPrime
- Vastaanotin Ecler
- Vastaanotin AudioControl
- Vastaanotin Rotel
- Vastaanotin Audio-Technica
- Vastaanotin Toa
- Vastaanotin Marantz
- Vastaanotin Rega
- Vastaanotin Vox
- Vastaanotin Pyle
- Vastaanotin Shure
- Vastaanotin Roland
- Vastaanotin NAD
- Vastaanotin Wet Sounds
- Vastaanotin JVC
- Vastaanotin VMV
- Vastaanotin S.M.S.L
- Vastaanotin Kicker
- Vastaanotin Auna
- Vastaanotin OSD Audio
- Vastaanotin DataVideo
- Vastaanotin Audizio
- Vastaanotin Bluesound
- Vastaanotin Blackstar
- Vastaanotin Hertz
- Vastaanotin Kenwood
- Vastaanotin Cambridge
- Vastaanotin MB Quart
- Vastaanotin Aplic
- Vastaanotin CSL
- Vastaanotin NUVO
- Vastaanotin IFi Audio
- Vastaanotin Henry Engineering
- Vastaanotin Block
- Vastaanotin Smart-AVI
- Vastaanotin Advance
- Vastaanotin Artsound
- Vastaanotin Denon
- Vastaanotin Marshall
- Vastaanotin Yorkville
- Vastaanotin Valcom
- Vastaanotin Mosconi
- Vastaanotin JBL
- Vastaanotin Infinity
- Vastaanotin Helix
- Vastaanotin Soundstream
- Vastaanotin Klipsch
- Vastaanotin PAC
- Vastaanotin Bellari
- Vastaanotin Rolls
- Vastaanotin Ground Zero
- Vastaanotin Karma
- Vastaanotin Glemm
- Vastaanotin EA
- Vastaanotin Match
- Vastaanotin Renkforce
- Vastaanotin Scansonic
- Vastaanotin SPL
- Vastaanotin Audiotec Fischer
- Vastaanotin Crunch
- Vastaanotin QSC
- Vastaanotin A-NeuVideo
- Vastaanotin Atlona
- Vastaanotin Classé
- Vastaanotin FoneStar
- Vastaanotin Monitor Audio
- Vastaanotin Peavey
- Vastaanotin Crown
- Vastaanotin Fosi Audio
- Vastaanotin Graupner
- Vastaanotin Antelope Audio
- Vastaanotin Vaddio
- Vastaanotin ESX
- Vastaanotin Omnitronic
- Vastaanotin Rocstor
- Vastaanotin Russound
- Vastaanotin MEE Audio
- Vastaanotin Monacor
- Vastaanotin GigaBlue
- Vastaanotin Mx Onda
- Vastaanotin Black Hydra
- Vastaanotin Electro-Voice
- Vastaanotin Boss
- Vastaanotin JL Audio
- Vastaanotin Shanling
- Vastaanotin Atlas Sound
- Vastaanotin Comica
- Vastaanotin Ashly
- Vastaanotin MuxLab
- Vastaanotin Audiolab
- Vastaanotin Lectrosonics
- Vastaanotin Memphis Audio
- Vastaanotin Alpine
- Vastaanotin Evolution
- Vastaanotin AVM
- Vastaanotin Primare
- Vastaanotin Elektrobock
- Vastaanotin PureLink
- Vastaanotin Kramer
- Vastaanotin ATen
- Vastaanotin Blustream
- Vastaanotin Mtx Audio
- Vastaanotin Yaesu
- Vastaanotin Musical Fidelity
- Vastaanotin Vimar
- Vastaanotin Phoenix Gold
- Vastaanotin Bogen
- Vastaanotin RDL
- Vastaanotin Harman Kardon
- Vastaanotin Dynacord
- Vastaanotin Ferguson
- Vastaanotin REL Acoustics
- Vastaanotin Inovonics
- Vastaanotin BZBGear
- Vastaanotin Bresser
- Vastaanotin Hotone
- Vastaanotin Phonic
- Vastaanotin Imperial
- Vastaanotin Hifonics
- Vastaanotin Crest Audio
- Vastaanotin Devialet
- Vastaanotin AudioSource
- Vastaanotin Taga Harmony
- Vastaanotin Strong
- Vastaanotin SoundTube
- Vastaanotin James
- Vastaanotin ButtKicker
- Vastaanotin Antelope
- Vastaanotin Futaba
- Vastaanotin AVMATRIX
- Vastaanotin Mooer
- Vastaanotin Rexing
- Vastaanotin Ram Audio
- Vastaanotin Marshall Electronics
- Vastaanotin Atoll
- Vastaanotin DAP Audio
- Vastaanotin Comprehensive
- Vastaanotin Inter-M
- Vastaanotin Esoteric
- Vastaanotin Konig & Meyer
- Vastaanotin Lumantek
- Vastaanotin Aguilar
- Vastaanotin Mark Levinson
- Vastaanotin Alto
- Vastaanotin Selfsat
- Vastaanotin Proel
- Vastaanotin Fiio
- Vastaanotin HiFi ROSE
- Vastaanotin Audibax
- Vastaanotin Luxman
- Vastaanotin Sound Ordnance
- Vastaanotin Wavtech
- Vastaanotin Dual
- Vastaanotin Parasound
- Vastaanotin Benchmark
- Vastaanotin KanexPro
- Vastaanotin InLine
- Vastaanotin Gefen
- Vastaanotin Vincent
- Vastaanotin Intelix
- Vastaanotin Lab Gruppen
- Vastaanotin GlobalSat
- Vastaanotin Koda
- Vastaanotin Technical Pro
- Vastaanotin Naim
- Vastaanotin Anthem
- Vastaanotin Audison
- Vastaanotin Loxjie
- Vastaanotin Clare Controls
- Vastaanotin Edwards Signaling
- Vastaanotin Nubert
- Vastaanotin VigilLink
- Vastaanotin SmartSystem
- Vastaanotin Harper
- Vastaanotin DARTS
- Vastaanotin ETON
- Vastaanotin Elipson
- Vastaanotin Streacom
- Vastaanotin Phonocar
Viimeisimmät Vastaanotin Käyttöohjeet
9 Huhtikuuta 2025
9 Huhtikuuta 2025
5 Huhtikuuta 2025
4 Huhtikuuta 2025
2 Huhtikuuta 2025
2 Huhtikuuta 2025
1 Huhtikuuta 2025
30 Maaliskuuta 2025
30 Maaliskuuta 2025
29 Maaliskuuta 2025