Currey & Company 9915 Käyttöohje
Sivut 1 Engels Lamppu
Lue käyttöohje merkille Currey & Company 9915 ilmaiseksi verkossa tai lataa PDF. Ohje on ollut hyödyllinen 41 henkilölle. Kysyttävää mallista? Esitä kysymys
Chandelier Installation Instructions
These instructions are provide for your safety. It is very important that they are read carefully
and completely before beginning installation of this chandelier. We strongly suggest that all
direct wired fixtures be installed by a professional electrician.
BEFORE ASSEMBLY
Your chandelier should have the following hardware included in the installation kit:
1. Canopy plate
2. Mounting strip with green ground screw
3. Threaded pipe nipple
4. Nipple assembly with locknut
5. Chain, electrical supply and ground wire
TO ASSEMBLE
1. Shut off the main electrical supply from the fuse
box/circuit breaker.
2. Remove existing fixture – loosen the locknut while
holding the canopy plate with one hand. Lower the
canopy plate. This exposes the outlet box that holds
the wiring.
3. Unscrew the plastic wire nuts and disconnect the black
and white house wires from the old fixture. Disconnect
the ground wire (save the wire nuts). Remove the
nipple and mounting strip that crosses the outlet box
and replace with new ones from installation kit.
4. Determine the distance to suspend your chandelier from
the ceiling and if necessary, remove the extra links from
the chain and reconnect the chain to the nipple (hook)
assembly. The electric supply wire that is woven through
the chain should be cut off 12 inches longer than the chain.
Cut the braided copper ground wire the same length. Split
the supply wire down the center by a length of 3 inches and
strip ¾ inch of insulation off the end of each wire. If you look very closely, you will
notice that the plastic insulation of one of the two split wires has a rib on the outside
edge. This ribbed wire is the “neutral” wire and the other is the “hot” wire; you will need
to remember the difference later on when you connect these to the house wires in the
electrical outlet box.
5. Insert the two stripped wires and the braided copper ground wire through the nipple
assembly, locknut, mounting plate and mounting strip. Using the wire nuts that you
saved, attach the ribbed wire to the white “neutral” house wire and the un-ribbed wire to
the black “hot” house wire. Secure the wire nuts with black electrical tape. Connect the
braided copper ground wire to the green ground screw marked “GRD” on the mounting
strip. It is imperative that the outlet box in your home be properly grounded.
6. Please note: Do not reverse the hot and neutral connections. Always make sure
that no wire strands are outside of the wire nut connectors.
7. Gently push the wiring back into the outlet box. Screw the nipple assembly, locknut and
canopy plate into the mounting strip and turn until the canopy is snug against the
ceiling. Please do not support fixture from the electrical cord.
8. Restore power to the electrical outlet box.
Care for your chandelier:
Dust with a soft dry cloth. To protect the finish, do not use cleaners or abrasives.
www.curreyandcompany.com
Tuotetiedot
| Merkki: | Currey & Company |
| Kategoria: | Lamppu |
| Malli: | 9915 |
Tarvitsetko apua?
Jos tarvitset apua merkille Currey & Company 9915 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Lamppu Currey & Company Käyttöohjeet
Currey & Company 9203 Käyttöohje Currey & Company 9078 Käyttöohje Currey & Company 9921 Käyttöohje Currey & Company 9636 Käyttöohje Currey & Company 9969 Käyttöohje Currey & Company 9007 Käyttöohje Currey & Company 9927 Käyttöohje Currey & Company 9935 Käyttöohje
Kaikki Currey & Company Lamppu käyttöohjeet
Lamppu Käyttöohjeet
Viimeisimmät Lamppu Käyttöohjeet
Beghelli Strada LED 46049 Käyttöohje Beghelli Strada LED 46050 Käyttöohje NEO Tools 99-076 Käyttöohje Philips Ultinon Essential LED 11972UE2X2 Käyttöohje Beghelli Strada LED 46016 Käyttöohje Beghelli Strada LED 46032 Käyttöohje Chauvet Wash FX Hex ILS Käyttöohje Ikan Helia HF70 Käyttöohje IKEA SAMBORD 005.869.49 Käyttöohje IKEA RÖDFLIK 405.827.08 Käyttöohje