Crane Speed and Cadence Sensor Käyttöohje
Crane
Ei luokiteltu
Speed and Cadence Sensor
Lue alta 📖 käyttöohje suomeksi merkille Crane Speed and Cadence Sensor (2 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 26 henkilölle ja sai 4.4 tähden keskimäärin 13.5 käyttäjältä
Sivu 1/2
User manual
SPEED & CADENCE SENSOR
GB
IRE
AFTER SALES SUPPORT 96044
YEAR
WARRANTY
GB
00800 52323000 00800 52323000
service@cranesportsconnect.com
MODEL:
AE8-SPCD-2 09/2018
PRODUCED IN CHINA FOR:
ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH
ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE.
Visit us at www.aldi.com
IRE
Great care has gone into the manufacture of this product and it should therefore provide you
with years of good service when used properly.
In the event of product failure within its intended use over the course of the rst 3 years aer
date of purchase, we will remedy the problem as quickly as possible once it has been brought
to our aenon. In the unlikely event of such an occurrence, or if you require any informaon
about the product, please contact us via our helpline support services, details of which are to
be found both in this manual and on the product itself.
Dok./Rev.-Nr. AE8-SPCD-2_BA_V5
3V
CR2032
1
2
3
4
5
6
7
8
9
9
10
4
3
11
6
5
3
2
1
9
3
1
9
A
B
D
C
2 mm max. 8
7
1
1
5
PACKAGE CONTENTS/DEVICE PARTS
1
Speed & cadence sensor (see )g. A, g. B, g. C, g. D
2
Sensor cover (see )g. A, g. B
3
Cable es, 6x (see g. A, g. B)
4
Cadence magnet (see )g. A, g. B
5
Speed magnet (see )g. A, g. B, g. C
6
Holder for speed magnet (see )g. A, g. B
7
Baery CR2032 (already inserted) (see g. A, g. D)
8
Cover for baery compartment (see g. A, g. D)
9
Opening (for cable es) of the speed & cadence sensor (see g. A, g. B)
10
Arrow marks (see ) g. A, g. B
11
Opening (for cable es) of the cadence magnet (see g. A, g. B)
GENERAL INFORMATION
Reading and storing the user manual
This user manual accompanies this speed & cadence sensor. It contains
important informaon on setup and use.
Before using the speed & cadence sensor, read the user manual carefully. This
parcularly applies to the safety instrucons. Failure to follow this user manual may
result in severe injury or damage to the speed & cadence sensor. The user manual is
based on the standards and rules in force in the European Union. When abroad, you
must also observe country-specic guidelines and laws. Store the user manual for
future use. Make sure to include this user manual when passing the speed & cadence
sensor on to third pares.
Explanaon of symbols
The following symbols and signal words are used in this user manual, on the speed &
cadence sensor or on the packaging.
WARNING!
This signal symbol/word designates a hazard with moderate degree of risk which may
lead to death or severe injury if not avoided.
NOTICE
This signal word warns against potenal damages to property.
This symbol provides you with useful supplementary informaon on
assembly or operaon.
Declaraon of conformity (see chapter “Declaraon of conformity”):
Products marked with this symbol meet all applicable EU Direcves for the
European Economic Area.
IPX7
The speed & cadence sensor is protected against immersion, up to 1 m
depth for up to 30 minutes.
Google Play™ and Android™ are trademarks of Google Inc. Apple, the Apple logo, iPad
and iPhone are trademarks of Apple Inc., registered in the USA and other countries. App
Store is a service mark of Apple Inc. The Bluetooth® word mark and logos are registered
trademarks of Bluetooth SIG, Inc. and are used under licence by Krippl-Watches. Other
trademarks and brand names are the property of their respecve owners.
SAFETY
Proper use
The speed & cadence sensor is exclusively designed for measuring your speed and
cadence and for exchanging data with smartphones and tablets. It is designed for
collecng data for analysis with the Crane Connect app. You can use this data to help
you reach your goals in terms of tness.
The speed & cadence sensor is only intended for private use and is not suitable for
commercial applicaons. It is not a children’s toy. Only use the speed & cadence sensor
as described in this user manual. Any other use is deemed improper and may result in
damage to property or even personal injury. The manufacturer or vendor accepts no
liability for damage caused by improper or incorrect use.
Safety instrucons
WARNING!
Danger of suocaon!
The speed & cadence sensor contains a baery and small parts. While playing, children
could swallow baeries, small parts, or package wrappings and choke.
• Keep the baeries, small parts, and package wrappings away from children.
• If a baery or small parts are swallowed, seek immediate medical aenon.
• Keep the speed & cadence sensor out of the reach of children.
WARNING!
Danger for children and persons with impaired physical, sensory
or mental capacies (e.g. parally disabled persons, older persons
with reduced physical and mental capacies) or lack of experience
and knowledge (e.g. older children).
This speed & cadence sensor is not intended for use by persons
with reduced physical, sensory or mental capabilies, or lack of
experience and knowledge, unless they have been given supervision
or instrucon concerning use of the speed & cadence sensor by a
person responsible for their safety. Children must not play with the
speed & cadence sensor. Cleaning and user maintenance may not
be performed by children unless they are under supervision.
• Keep children away from the speed & cadence sensor.
• Do not let children play with the packaging wrapper. They
could swallow it and suocate.
Further informaon and this user manual can be found at www.krippl-watches.com
(under “Customer Service”).
NOTICE
Risk of damage!
Improper handling of the speed & cadence sensor may result in damage to the speed &
cadence sensor. You can use the speed & cadence sensor at ambient temperatures between
0 °C and +50 °C. Do not expose the speed & cadence sensor to permanent moisture.
Avoid dust, heat and connuous exposure to direct sunlight. Never try to repair the
speed & cadence sensor yourself. For technical problems, contact the service address
indicated on the warranty card.
Avoid strong magnec elds (e.g. transformers). Otherwise, this may cause
uctuaons in the transmission of the data measured.
WARNING!
Risk of explosion and chemical burns!
Improper handling of baeries poses the risk of explosions or chemical burns caused by
leaking baery acid.
• Never expose the baeries to excessive heat, such as sunlight,
re or similar – increased risk of leakage!
• Do not charge or reacvate the baeries, do not disassemble
them, do not dispose of them in re and do not short circuit
them.
• Baeries may pose a risk to health if ingested. You should
therefore store the baeries so that they are not accessible to
children. If you suspect that a baery has been swallowed or
otherwise incorporated, seek immediate medical aenon.
• If baeries leak, use gloves to remove them. Aerwards, clean
the baery compartment with a cloth without water or any
cleaners.
• Only have the baery replaced with the same baery type.
• Do not allow baery acid to come into contact with skin, eyes
or mucus membranes. In the event of contact with baery acid,
immediately ush the applicable areas with plenty of clean
water and consult a doctor if necessary.
• Dispose of baeries at your collecon point.
• Keep the user manual for baery informaon.
• Further notes and informaon on changing the baery can be found in the chapter
“Changing the baery”.
CHECKING THE SPEED & CADENCE SENSOR AND PACKAGE
CONTENTS
NOTICE
Risk of damage!
If you are not cauous when opening the packaging with a sharp knife or other pointed
objects, you may damage the speed & cadence sensor.
–Be careful when opening the package.
1. Remove the speed & cadence sensor
1
from the packaging. Remove the
packaging material and protecve labels from the speed & cadence sensor. Keep
the packaging materials away from children and dispose of the materials in an
environmentally friendly manner.
2. Check whether the product contents are complete and if the speed & cadence
sensor is damaged or not (see ).g. A
3. If the delivery is incomplete and/or if parts are damaged, do not use the speed &
cadence sensor. Contact the manufacturer via the service address indicated on the
warranty card.
FUNCTIONS
You can use the speed & cadence sensor to measure/record your speed and cadence
during a workout.
This data is transmied to a device, e.g. your smartphone. The free Crane Connect app
allows you to analyse this data in depth. Once installed, the Crane Connect app will
provide you with the following informaon regarding your workout:
• Duraon of workout
• Distance covered
• Cadence measurement
• Speed measurement
• Lap mes
• Calorie consumpon
• Route map
COMPATIBLE BLUETOOTH® DEVICES
The following devices with Bluetooth® 4.0 or higher are compable with the speed &
cadence sensor
1
and the Crane Connect app:
• Apple® iPhone® 4s and more recent versions
• Apple® iPad® 3rd generaon and more recent versions
• Apple® iPad mini™
• Apple® iPad Air™ and more recent versions
• Smartphones and tablets with Android™ 4.3 and more recent versions
You can nd a complete list of supported devices online at
www.cranesportsconnect.com/compability.
CRANE CONNECT APP
Downloading and installing the Crane Connect app
For using the speed & cadence sensor
1
you must download the Crane Connect app
and install it on your compable Bluetooth® device.
–Download the free Crane Connect app from the App Store, from the Google Play
Store, at www.cranesportsconnect.com under the “Download” tab or via the
following QR codes.
QR code for Android QR code for iOS
To avoid long download mes and the associated costs, it is recommended
that you use a Wi-Fi connecon for downloads.
– Install the Crane Connect app on your compable Bluetooth® device. Follow the
step-by-step instrucons for this.
Creang a user account
To create a user account with the Crane Connect app, proceed as follows:
1. Start the Crane Connect app.
2. Follow the registraon instrucons step by step.
3. To perform user and product-specic sengs, select the icon “All Sengs”.
You can also create new users on the website www.cranesportsconnect.
com.
Connecng the speed & cadence sensor with the Crane Connect
app
Make sure that the Bluetooth® funcon on your smartphone has been
acvated.
1. Once the user sengs are complete, return to the “All Sengs” menu.
2. Select the icon “Speed & Cadence Sensor”.
You can change the sengs for opmal use of your speed & cadence sensor.
3. To connect the speed & cadence sensor
1
with your smartphone, select
“Connect” in the “Pairing” eld.
A nocaon window will appear.
4. In this window, press “Pair now”.
The speed & cadence sensor will connect automacally to the app
We would recommend to take either the speed magnet
5
or the
cadence magnet
4
and move it across the corresponding arrow mark
10
on the speed & cadence sensor
1
, with a maximum distance
of approx. 2 mm between speed & cadence sensor and magnet during the
connecon process.
5. From there, you can start the measurements and access the analyses of your
measured data via the “Speed & Cadence Sensor” icon.
As soon as you have connected the speed & cadence sensor with the Crane
Connect app, all measured data will be transferred to it.
Tuotetiedot
| Merkki: | Crane |
| Kategoria: | Ei luokiteltu |
| Malli: | Speed and Cadence Sensor |
Tarvitsetko apua?
Jos tarvitset apua merkille Crane Speed and Cadence Sensor esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Ei luokiteltu Crane Käyttöohjeet
26 Helmikuuta 2025
Ei luokiteltu Käyttöohjeet
- Ei luokiteltu Bluetti
- Ei luokiteltu Singularity Computers
- Ei luokiteltu Tork
- Ei luokiteltu Carlsbro
- Ei luokiteltu Vivotek
- Ei luokiteltu CubuSynth
- Ei luokiteltu T-Rex
- Ei luokiteltu Shimbol
- Ei luokiteltu Adventuridge
- Ei luokiteltu Revlon
- Ei luokiteltu Black Lion Audio
- Ei luokiteltu Paradigm
- Ei luokiteltu One For All
- Ei luokiteltu Casablanca
- Ei luokiteltu Caberg
Viimeisimmät Ei luokiteltu Käyttöohjeet
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025
9 Huhtikuuta 2025