Austral Super 5 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Austral Super 5 (6 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 57 henkilölle ja sai 4.6 tähden keskimäärin 8 käyttäjältä

Austral Clothes Hoists Pty. Ltd.

Incorporated In Victoria A.B.N.: 68 006 790 727

32-34 Hydrive Close, Dandenong South 3175, Australia

Tel: (03) 9799 8122, Fax: (03) 9799 8266

International Tel: +61 3 9799 8122, Fax: +61 3 9799 8266

www.australclotheshoists.com.au

admin@australclotheshoists.com.au

Installation Instructions for: Super & Deluxe Hoists

Your Austral Rotary Clothes Hoist is designed to last a long time. It is important to follow these instructions so you will

enjoy the benefits of a properly installed hoist. Incorrect installation could damage your hoist and/or void your guarantee.

If at any time your Austral Hoist should not function correctly or if spare parts are requiredcall your state distributor ,

listed on the guarantee page.

Site Selection & Digging (S- teps 1 3)

Important: Before digging, ensure the area is safe and clear of electrical, gas and plumbing services etc (refer to Dial Before

You Dig (Aus), beforeUdig (NZ), any architectural drawings etc).

1 1. Select a site that gives 1m clearance to the end of each arm of the hoist (2m more than hoist’s diameter), see Figure

2 P lace Handle Shaftthrough Handle Grip then

tap into hole in Handle Arm whilstsupporting

behind the A rm with a chock,seeFigure 2.

Turn the handle antiensure the- clockwiseto

hoist is wound down as far as itgoes. Also fit

Handle Cover to Deluxe models.

3 Ensure it is safe to dig at the selected site. At its centre, startdigging

- a hole 150200mm in diameter. Dig the hole deep enoughsothat

Cwhenthe olumn is stood upright in the hole the Reducer is levelwith

theuser’s head height, see Figure 3. A depth of 550mmwill resultin

the Crossbeing1700mm high and the outer lines being approximately 1850mmhigh when

the hoistiswound down. After height is set, allow Column to lean over and rest in the hole.

3a Deluxe models only: remove the olumn frCom the hole and insert the Steel Rod through the

pre-drilled holes in the bottom of the olumn back in the hole. CColumn. Place Note:

instead of Steel Rod, Super modelshave a crimped bottom a tube to hold firm in concrete.

Equipment Required

Spirit level, crowbar, shovel, , pliers, concrete, drainage gravel, tape measurescrewdriver

Parts Supplied

Qty

Description

Part Number

1

Rotary or Helical Column

R/COL (Super)or H/COL(Deluxe)

4

Arms (m 1975mor 2475mm)

RH01AR06A (4mmodel) or ) (5mmodel

1

Handle Grip, Black Plastic

FRC11

1

Handle Shaft, Black Plastic

FRC12

4

Round End Caps, Black Plastic

R19

1

Wire Roll (50m or 70m)

R14 or R15

4

Tubular Stays (150095mm or 19mm)

RH03AR08A (4m model)or (5m model)

4

Bolt, 35mm x 6mm

FA18

4

Bolt, 20mm x 6mm

RH04

8

Nylon Lock Nut, 6mm

FRC22

4

Washer, 6mm

R18

Deluxe Hoists only:

1

Handle Cover, Black Plastic

HE03

1

Steel Rod, 150mm x 8mm

FA24

Tuotetiedot